in fact i get a lot of 'does anyone have a microscope and some tweezers' type comments when the hood is up on the car.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
V8 in a suzuki
I would expect that the turbos would be pretty small... the one on my engine has a fan (for lack of a better term) that is approximately 40 - 50mm in diameter... so it's pretty small...
in fact i get a lot of 'does anyone have a microscope and some tweezers' type comments when the hood is up on the car.
in fact i get a lot of 'does anyone have a microscope and some tweezers' type comments when the hood is up on the car.
DMA Founding Member #1 - Now Retired
greg wrote:I would expect that the turbos would be pretty small... the one on my engine has a fan (for lack of a better term) that is approximately 40 - 50mm in diameter... so it's pretty small...
in fact i get a lot of 'does anyone have a microscope and some tweezers' type comments when the hood is up on the car.
Your impeller is very small ( 40-50mm) as is its housing. My last car was a 500HP 300 ZX twin turbo. When it was standard, the factory turbos wouldn't start to make any boost till 3500. Thats pretty high in the revs to START boosting. When I fitted the high flow garret ball bearing units, they were capable of flowing 50% more air, so you would expect alot more ;lag. But due to the higher quality components used, it came on full boost just 300rpm later than the factory units. Because this 1.6 is a 'V' configeration, you can pretend that it is 2 800cc motors side by side. Therefor the turbos would be slightly bigger that yours greg, But they would not have been restricted to the same manufacturing budget as a mass produced engine like yours. The result is a larger than expected turbo, with high flowed housings, larger impellers, ball bearing inserts, carbon rings and seals for high temp etc etc and a very early spool up, giving higher, sustained boost throughout a larger portion of the rev range.
Max wrote:Do you have any pics of your engine? Ive been looking for a small turbo for a long time but in my country they are very hard to find. Somthing like a charade or starlet turbos. How much did it cost the entire turbokit and the instalation? How much psi is it blowing?
Max, i'm not sure if this will help you, but there are some shots on this japanese site of a fellow who is building up his F6A/K6A jimny motor...
http://www.geocities.co.jp/MotorCity-Ra ... index.html
some of the links show the fitment of a new turbo onto it too - but i don't know what it's out of, and i don't speak japanese either.
Cheers
DMA Founding Member #1 - Now Retired
If most oif the V8's are to big .. why not a nice light alloy blocked V6 like the Nissan VG30 they cost about $600 for a complete motor .. about $1200 for a front cut .. If you blow it up .. just replace the entire motor with another good runner from a wrecker.
Hmm whole motor\gearbox (auto) and T/case from a pussfinder with rockhopper gears .. plenty of power and lotts of strength .. No idea if it could actually be made to fit
Hmm whole motor\gearbox (auto) and T/case from a pussfinder with rockhopper gears .. plenty of power and lotts of strength .. No idea if it could actually be made to fit
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
greg wrote:Max wrote:Do you have any pics of your engine? Ive been looking for a small turbo for a long time but in my country they are very hard to find. Somthing like a charade or starlet turbos. How much did it cost the entire turbokit and the instalation? How much psi is it blowing?
Max, i'm not sure if this will help you, but there are some shots on this japanese site of a fellow who is building up his F6A/K6A jimny motor...
http://www.geocities.co.jp/MotorCity-Ra ... index.html
some of the links show the fitment of a new turbo onto it too - but i don't know what it's out of, and i don't speak japanese either.
Cheers
i can read it no worries. if I use
http://babelfish.altavista.com/
put in the url and choose jap - eng. and you're all set.
Skippy
--------------------------------------------------
for all things digital, come to NEWflavour
'a better tasting multimedia experience'
http://www.newflavour.com/
--------------------------------------------------
--------------------------------------------------
for all things digital, come to NEWflavour
'a better tasting multimedia experience'
http://www.newflavour.com/
--------------------------------------------------
hey! thanks for all the info about the engine. And Thanks for the translation website too. 
BTW, who owns that zook? It looks like a mix between a hummer and a mercedes benz. Is he trying to do a 10sec drag rocket or just the ultimate zuk? That guys spent some serious money on it.
If any of you had to choose between the F6A/K6A and the 1.6 16v EFI, wich would you choose? I'm just making plans for the future because in my coutry, getting the 1.6 efi is pretty easy and the k6a is a bit harder to get, but still doable.
BTW, who owns that zook? It looks like a mix between a hummer and a mercedes benz. Is he trying to do a 10sec drag rocket or just the ultimate zuk? That guys spent some serious money on it.
If any of you had to choose between the F6A/K6A and the 1.6 16v EFI, wich would you choose? I'm just making plans for the future because in my coutry, getting the 1.6 efi is pretty easy and the k6a is a bit harder to get, but still doable.
without the gearing options of the sierra (6:1 transfre case gears that drop high range some 22 to 23% as welll as diff gears dropping from 3.73 to 5.13 etc) the cappo motor would most lilkley not be a terribly good swap as it would be operating way out of it's powerband. As well as issues with gearbox and T/case (as the vit tcase and gearbox are all "one piece" unlike the sierra where the gearbox and T/case are tied together by a driveshaft ..
The 16v 1.6 EFI motor in a vit would be a much more sensible swap .. Also one of the reaons greg did it was he was looking at diet wheeling, wanting to run the lightest sierra he could sensibly do ... and a 3 cyl 660cc motor certainly fits that bill
The 16v 1.6 EFI motor in a vit would be a much more sensible swap .. Also one of the reaons greg did it was he was looking at diet wheeling, wanting to run the lightest sierra he could sensibly do ... and a 3 cyl 660cc motor certainly fits that bill
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Who is online
Users browsing this forum: No registered users and 17 guests