Three head bolts on a Holden Astra are being a pita, we continued with one until it was a mangled mess and after spending three hours have admitted defeat for the day.
We have forced a smaller socket over it, tried it with vice grips, welded a nut to it and yelled at it.
After welding a nut to it it has become soft and any attempt at grabbing it with vice grips is futile.
Can only think of drilling the head off the bolt and sliding the engine head over it.
Anyone else got other ideas??
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Burred head bolt
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Burred head bolt
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
I had a similar problem years ago with my mothers Mazda 808. It had a blown head gasket but the head bolt was corroded into the head. Ended up drilling the head of the bolt off then using timber wedges to wedge the head off. Being an alloy head this did it no good at all I needed to get a second hand head from the wreckers. The remaining bolt easily unscrewed from the block.
The head is going to the head doctor after a blown timing belt and twin cam....
I only became involved because these guys don't have the tools to do the job etc. I'm not sure if they are cashed up to pay a thread fella etc.
So drilling sounds good then??
I only became involved because these guys don't have the tools to do the job etc. I'm not sure if they are cashed up to pay a thread fella etc.
So drilling sounds good then??
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
Would screw extractors work ?
I had a bolt that was stuck in the back of the zook, I was tightening it up and it's thread in the body was a little chocked with crap and rust. So it wasn't going in easily and due to it's age, the head of the bolt actually sheared off from the force of spinning it
Just drilled a hole in the middle of it and the screw extractors worked like a charm.
I had a bolt that was stuck in the back of the zook, I was tightening it up and it's thread in the body was a little chocked with crap and rust. So it wasn't going in easily and due to it's age, the head of the bolt actually sheared off from the force of spinning it
Just drilled a hole in the middle of it and the screw extractors worked like a charm.
04 Ford Courier TD
Bye, bye Sierra... :'(
Bye, bye Sierra... :'(
get a set of parrot beak stiltsons they grip every thing . i got a set form bunnings for $30 had to use it on shower tap bodys to change washers . tebodys where seriosly corroded . it got them of and i was two hands swinging off them and they didnt stip just held on and cracked the corroed tap body came out easy.
ya got2 b tuff if u gunna b dumb!!
I'd try that, and if still no go i.e. the metal is that soft, drill the top off, remove the head - that will relieve tension on the bolt probably making it easier to remove, then put the stillsons back on a bit lower, and or soak the bottom of the thread where the bolt goes into block overnight with some crc etc.jugger wrote:get a set of parrot beak stiltsons they grip every thing . i got a set form bunnings for $30 had to use it on shower tap bodys to change washers . tebodys where seriosly corroded . it got them of and i was two hands swinging off them and they didnt stip just held on and cracked the corroed tap body came out easy.
There are no stupid questions, but there are a LOT of inquisitive idiots
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
It has been suggested, she let the rego lapse because it isn't running thus it isn't insuredBarney7779 wrote:remove plates from car and push it down the road and ring bacon and report it stolen, then buy new car witn insurance payout
Drill head off bolt then slide head over the left over stud.
Once pressure is off bolt and head removed you will be able to undo the remaining part of the bolt by hand
There has been a few car fires around here lately
[quote="fool_injected"]
I pity my brother when she is a teenager[/quote]
I pity my brother when she is a teenager[/quote]
no really sure if this would work ?
Grab a grinder then re surface the sides of the bolt head.
The other way would be to grab a 1mm cutter disc and turn the bolt into a flat head screwdriver bolt/head, probably not going to do much really
I'm sort of in the same bind got 2 screws where the top has sheared off and the thead is stuck inside the holes, don't want to re drill then tap.
Where are these screw doctors?
what are and where to buy the screw extractor tools?
Grab a grinder then re surface the sides of the bolt head.
The other way would be to grab a 1mm cutter disc and turn the bolt into a flat head screwdriver bolt/head, probably not going to do much really
I'm sort of in the same bind got 2 screws where the top has sheared off and the thead is stuck inside the holes, don't want to re drill then tap.
Where are these screw doctors?
what are and where to buy the screw extractor tools?
Last edited by zagan on Sun Jan 28, 2007 9:09 pm, edited 1 time in total.
Look for a post by V8patrol in 4x4 tech about removing stuck bolts/nuts .. lots of useful stuff in there.
Cut the bolt head off, remove the head, smack the bolt a few times and then heat the area around the thread to expand the metal, apply a penetrating oil and weld a bolt to the top of the headless bolt .. hopefully all the mechanical shock and the fact the bolt is no longer stretched (like the lid on a jar, break the vacuum seal and it unscrews easily) .. It should come out no worries.
If not then try the eziouts etc and good luck following that course .. you will need it ..
Cut the bolt head off, remove the head, smack the bolt a few times and then heat the area around the thread to expand the metal, apply a penetrating oil and weld a bolt to the top of the headless bolt .. hopefully all the mechanical shock and the fact the bolt is no longer stretched (like the lid on a jar, break the vacuum seal and it unscrews easily) .. It should come out no worries.
If not then try the eziouts etc and good luck following that course .. you will need it ..
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
And harder than any drill bit when (not if) they snap. So you can't get these out...Dooley wrote:I got some screw extractors from bunnings IIRC.
Something like $30 for a pack of 5 sizes, without coresponding drill bits, kincrome brand.
They're just a tapered, coarse, reverse thread bolt thing.
Posting quality not quantity!
Wanted: Stock HiLux Front Leaf Springs
Wanted: Stock HiLux Front Leaf Springs
I had to drill through/out a snapped masonary bit a few weeks back, my trusty ARTU's took a while bit it got there.. (ever seen the guy at 4x4 shows drilling lots and lots of holes in a wiltshire files ... slow but work great)Bad JuJu wrote:
And harder than any drill bit when (not if) they snap. So you can't get these out...
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
I'll have to check them out as the screws seem to be stuck in a bar in the front holds up the 8mm bash plate, 2 have broken only 1 old bolt holding the thing together now, that's why I want something that I can push the screw through etc.Dooley wrote:I got some screw extractors from bunnings IIRC.
Something like $30 for a pack of 5 sizes, without coresponding drill bits, kincrome brand.
They're just a tapered, coarse, reverse thread bolt thing.
need to fix it up proper other wise something bad will happen 1 day.
fix it! bad things do happen!
I'll have to check them out as the screws seem to be stuck in a bar in the front holds up the 8mm bash plate, 2 have broken only 1 old bolt holding the thing together now, that's why I want something that I can push the screw through etc.
need to fix it up proper other wise something bad will happen 1 day.
http://s44.photobucket.com/albums/f17/d ... whoops.jpg
the remainder of my bashplate after it caught on a log when getting snatched out backwards. the screw on the corner that caught was missing.
Just got to be gentle, preferably use a tap wrench. A good old adjusting was used in this case but from what I've been told that tends to result in snapping.Bad JuJu wrote:And harder than any drill bit when (not if) they snap. So you can't get these out...Dooley wrote:I got some screw extractors from bunnings IIRC.
Something like $30 for a pack of 5 sizes, without coresponding drill bits, kincrome brand.
They're just a tapered, coarse, reverse thread bolt thing.
Well the whole point is they are hard so can bite into other metals and make a thread, yet being hard makes them brittle.
04 Ford Courier TD
Bye, bye Sierra... :'(
Bye, bye Sierra... :'(
Who is online
Users browsing this forum: No registered users and 0 guests