Outer Limits 4x4 Board

more info on these injectors-

5.0 LTR BOSCH INJECTORS - This set came out of VR HSV Clubsport prior to stroking
They have been ultrasonically cleaned, tested and serviced. Filter Baskets have been changed and all upper and lowers seals have been replaced.




Are these ones gonne be ok or not

well to start with I was pretty sure you fuel rain connector is different to those - I think you have hoses that go directly to the top of each injector on your rangie where as these are more like the hotwire/3.9L injector rail connector.

Give us the part number of those bosch injectors and I will check the flow rate. Off the top of my head I thought the 5.0L Holden V8 injectors
only flowed 150cc/min vs 167 or so cc/min for the 3.9/3.5 rangie

At least that is what my research has showed. I didn't want my engine running any leaner on fuel than it already was. There are some good listings on the web with injector rates and details so give me the info and I will look it up

Tom

Well there here
They are exactly the ones in the pic and after inspecting my current 3.5 injectors the fuel rail connection looks the same

BUT I dont have the model number for these bocsh ones

This might be of use to you guys:
http://www.msefi.com/viewtopic.php?t=2576

Loads of injector info there.

Guy just though i would update it seems I will have to change the fuel rail to get these injectors in

AnthonyP
Did the 5.0 injectors work?
I am doing a 3.5 to 4.6 upgrade , and am using my 3.5 manifold.

Nairbo

Holden injectors and hotwire 3.5-3.9 onward injectors have an o ring at the top and bottom and slot into a socket in the rail while flapper 3.5 injectors have a pipe at the top . Rangee had to buy a 3.9 rail before he could upgrade injectors to Holden 5 litre. He recently fitted a Thor manifold and rail and had to back off the fuel pressure to get the car to start with 4 litre injectors which are rated at 22.5 LB but at 3.5 Bar
The Holden 5 litre injectors are smaller at 18.5 lbs per hour than 3.9 injectors at 22.5Lb per hour. I bought Bosch 4 hole replacements from USA for about $80 each.
So you need a 3.9 rail. If going 4.6 , I think 3.9 injectors would be better than Holden. But you could get over it by increasing fuel pressure, if you are running an afternmarket ECU.
I can sell you a good set of 3.9 injectors, 6 with 110,000KM and cleaned within 10,000K and two new as 2 died in cleaning. I fitted a Thor manifold and fitted Bosch "pink" 4 holes at the same time.
I also have a 4.0 litre rail and Bosch "green" 4 hole injectors . I do not know whether the 4.0 l rail will fit a 3.5 manifold. I think so as a 3.9 rail will "just" fit a Thor manifold, but there are issues with fitting a fuel pressure reg etc.
Regards Philip A

How many $ for each set of injectors ?
Do both sets" look" the same size?

Brian

The green Thor injectors are shorter by about 10MM, and the rail is correspondingly further apart than the 3.9 rail. On reflection the 4.0 rail does fit the 3.9 manifold, but you would need to use an aftermarket regulator.
Email me on parmbruster@optusnet .com.au and we can discuss price and I can email you photos.
Regards Philip A

So did anyone ever fit V8 commodore injectors in there Land rover V8

I'm running Mustang 4.6 (4 hole) injectors on my p76 with rover 3.9 hotwire injection system they plug staraight in idles smooth and better throttle response.

91rangie wrote:I'm running Mustang 4.6 (4 hole) injectors on my p76 with rover 3.9 hotwire injection system they plug staraight in idles smooth and better throttle response.

Do you have a part number for these injectors ?

91rangie wrote:I'm running Mustang 4.6 (4 hole) injectors on my p76 with rover 3.9 hotwire injection system they plug staraight in idles smooth and better throttle response.

Where did you get them from and how much were they if you dont mind me asking?
Cheers

TuffRR wrote:I'd imagine the 3.8 V6 injectors would be sweet with the 3.5 as Rovers generally run on the lean side apparently.

lol

Sprover wrote:

91rangie wrote:I'm running Mustang 4.6 (4 hole) injectors on my p76 with rover 3.9 hotwire injection system they plug staraight in idles smooth and better throttle response.

Where did you get them from and how much were they if you dont mind me asking?
Cheers

nairbo wrote:

91rangie wrote:I'm running Mustang 4.6 (4 hole) injectors on my p76 with rover 3.9 hotwire injection system they plug staraight in idles smooth and better throttle response.

Do you have a part number for these injectors ?

http://cgi.ebay.com/ebaymotors/MUSTANG- ... ccessories

They are gen 2 not gen 3 (not the engines) design

I too am runngin the Bosch Gen 3 injector to suit a mustang aswell.
I also purchased mine off ebay.

I have been running a set of VR V6 commodore injectors in my early 3.5 disco for about 3 years now without issue. They just slotted straight in. Got them cheap off ebay. Would have gone the mustang ones but I was being cheap!!

John