Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Cutting steel sheet ( edit ) using a Nibbler ?

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 1644
Joined: Thu Aug 03, 2006 9:50 pm
Location: Hawkesbury, Sydney

Cutting steel sheet ( edit ) using a Nibbler ?

Post by CWBYUP »

Just looking at a way to cut steel sheet for the camper trailer.

I have seen some nibblers that cut up to 4 mm which would be good incase I need them for something else down the track.

Is there some thing else I should be looking at ?

Plasma would be nice but i want a cleaner edge on the cut.

Its mainly for 1 or 2 mm but i would be nice to be able to cut up to 3 or 4mm.

Thanks for any info.

Cheers Nick
Last edited by CWBYUP on Fri Jun 01, 2007 11:36 pm, edited 1 time in total.
[quote="Vulcanised"]more grunt than a row of drunk girls at a B&S ball!
[/quote]
Posts: 436
Joined: Sun Jun 13, 2004 3:02 pm
Location: Building true offroad trailers and campers

Post by dieseldude »

I'm building a camper trailer at the moment and have been using the good old 9 inch angle grinder with a metal cut off wheel on it.

It's noisy as hell, hard work - but it gets the job done!

I suppose you have to make do with what you have......

Anthony
Droughtmaster Offroad Trailers and Campers

Offroad Camper MkI - Build up:
http://www.outerlimits4x4.com/phpBB2/viewtopic.php?t=106712
Posts: 1644
Joined: Thu Aug 03, 2006 9:50 pm
Location: Hawkesbury, Sydney

Post by CWBYUP »

yeah 9" is fine but i want a easyier more profesional finish to it.

no offence to your work but using a 9" its ever hard to get perfectly straight which i need for what i'm doing.

Any one else got any other ideas ?

Cheers Nick
[quote="Vulcanised"]more grunt than a row of drunk girls at a B&S ball!
[/quote]
Posts: 68
Joined: Wed Jun 01, 2005 12:36 pm
Location: Albany Creek

Post by keencdk »

I just use a jigsaw and steel cutting blades, take it nice and slow and they are as acurate as your ability to follow a line
Posts: 3385
Joined: Fri Sep 17, 2004 8:26 pm
Location: Melbourne

Post by shakes »

take the sheet to somewhere with a gilotine :D
Posts: 141
Joined: Wed Mar 02, 2005 5:59 pm
Location: bendigo

Post by AdrianGQ »

take it to a fab shop and get it cut in a guilotine will cost you bugger all and be straighter than you could get it with any of the other methods mentioned
Posts: 322
Joined: Fri May 21, 2004 12:10 am

Post by Steve F »

I use a 4" grinder with 1mm disk and a piece of box section clamped on to the piece being cut as a guide, get a good straight line and easy to do. Those 9" ones are a bugger being so big and the small ones cut through the thin stuff easily.

Cheers
Steve
Posts: 1048
Joined: Sat Jul 17, 2004 9:48 am
Location: Waikerie; SA

Post by Eddy »

'nuther vote for the 4" x1mm disc.

those things are great.
Posts: 412
Joined: Fri Jul 14, 2006 6:03 pm
Location: brisbane

Post by rvh96 »

Steve F wrote:I use a 4" grinder with 1mm disk and a piece of box section clamped on to the piece being cut as a guide, get a good straight line and easy to do. Those 9" ones are a bugger being so big and the small ones cut through the thin stuff easily.

Cheers
Steve
x3
'05 GU Patrol coil cab ST
6" lift
Tough dogs
Snake Racing drop arms
3rds Rear Arms
Twin ARB air lockers
37" trepadors
ARB bullbar
WARN winch
High flow turbo
3" mandrel bent exhaust
Posts: 8556
Joined: Mon Jun 13, 2005 9:34 pm
Location: Sydney

Post by RockyF75 »

rvh96 wrote:
Steve F wrote:I use a 4" grinder with 1mm disk and a piece of box section clamped on to the piece being cut as a guide, get a good straight line and easy to do. Those 9" ones are a bugger being so big and the small ones cut through the thin stuff easily.

Cheers
Steve
x3
yep

that or the guillotine at a sheety's place. Bring a beer and the sheet marked out and it will be done in no time
60 + Turbo, 33"s :armsup:
Posts: 2176
Joined: Sat May 31, 2003 1:30 am
Location: BrisVegas

Post by Mad Cruiser »

Steve F wrote:I use a 4" grinder with 1mm disk and a piece of box section clamped on to the piece being cut as a guide, get a good straight line and easy to do. Those 9" ones are a bugger being so big and the small ones cut through the thin stuff easily.

Cheers
Steve
Yep that's what i do, easier and cheaper ;)
1998 Toyota Landcruiser 100 series GXL
1976 FJ45 Landcruiser ute
Posts: 109
Joined: Wed Mar 14, 2007 4:24 pm
Location: Brisbane, Qld

Post by peeko22 »

if your in brisbane i can cut it for you i am a sheety? a gilo is really the only way
Email - flossamarosus@hotmail.com
Posts: 300
Joined: Sun May 20, 2007 2:22 am
Location: Toowoomba QLD

Post by 90Mav »

I use an air hammer(chisel) with a sheet metal cutter, works well for up to 1.2mm.
It is like a 3 prong fork with the middle leg bent down, cuts a 3mm or so strip out of the sheet, nice clean cut... but cant do corners(neatly).
Thrashed '90 Leaf spring Maverick ute, TD42, 2" EFS lift. 36 Swampers.
Posts: 1187
Joined: Sat Nov 01, 2003 5:05 pm
Location: melbourne, Knoxfield

Post by matthewK »

Gilo is one of a few ways not the only way , i can get a just as nicer cut using the Quickie on trackes set right, plasma cut it or if ya ruff as guts grinder and a cut off disc
1995 land rover disco on 265 muddies
Posts: 142
Joined: Wed Jan 19, 2005 2:13 pm

Post by MY92SURF »

Just on a side note to the 1mm discs... head down to someone like Coventry's, Blackwoods, Bakers, BOC or any of your industrual suppliers and ask for a Flexovit 0.89mm wheel. They're even faster and neater cutting than a 1mm, and are depressed centre(raised hub) so they'll cut flush up against the bit of box clamped on.

They're available in 4.5" for handyman grinders, and 5"
Posts: 1644
Joined: Thu Aug 03, 2006 9:50 pm
Location: Hawkesbury, Sydney

Post by CWBYUP »

The general feelling i'm getting no one uses a nibbler.

Is there any reason for this ?

I have a fair bit of sheet to cut and would like to do it at home if possible but dont want to spend money on a nibbler and it be shit.

Any one help me ?

And thanks anyway champ but I'm down in Sydney.

Nick
[quote="Vulcanised"]more grunt than a row of drunk girls at a B&S ball!
[/quote]
Posts: 3064
Joined: Sun Jun 12, 2005 11:00 pm
Location: Yinnar South, Vic

Post by cloughy »

You need somewhere that has a profile cutter, your local sheety, so long as their a big enterprise ;) , better than any plasma, grinder, guillotine, or tin snips
Wanted: Car trailer or beaver tail truck, let me know what you got
Posts: 1443
Joined: Tue Apr 12, 2005 3:57 pm
Location: Brisbane

Post by vanbox »

im a builder and use a nibbler for roofing and some small sheet work. they are good and fast, however very messy and dangerous with a lot of waste (mine about 5mm). without a track very hard to keep straight, and the underside of the sheet you cut can have a semi-sharp edge on it. not worth the money if your after a quality straight cut. excellent for corners.

my 2c

PAUL
MUD BEERS and MAYHEM

DURAMAX POWERED GU
Posts: 19062
Joined: Sat Oct 25, 2003 11:39 pm
Location: In a horse near you

Post by chimpboy »

CWBYUP wrote:The general feelling i'm getting no one uses a nibbler.

Is there any reason for this ?

I have a fair bit of sheet to cut and would like to do it at home if possible but dont want to spend money on a nibbler and it be shit.

Any one help me ?

And thanks anyway champ but I'm down in Sydney.

Nick
I have a nibbler. I use it occasionally, it's way faster than a jigsaw or grinder and it cuts nice and cleanly. It has served me well in cutting holes in guards for snorkels and other situations where I've cut holes in panels in tricky spots.

Probably the negative is that it's harder to control than a jigsaw because it's faster. I've never actually tried to do a long straight cut with it, but if I did I would use a piece of 20x20 angle or so as a guide, and I would think that this would allow a 100% perfect straight cut. I can cut straight with it without a guide over a short distance. If you have a space where you can put what you're cutting up on a bench or stands, and fix a guide to it, I think a nibbler might work for you.

I agree with Vanbox ^^^ it is hard to keep straight without some kind of guide, and it spits out a huge amount of little )-shaped pieces. Mine doesn't waste 5mm in the cut, probably more like 3mm.

I understand why you don't want to fork for one without testing. Mine was about $100 and I've used it probably 10 times in three years. The thing is though that even with rare use, it's so useful on the rare occasions when you need it that it's worth the $$ imho. It'd be good if you could borrow one to experiment with. Maybe you could buy one at Supercheap, try it, and if it doesn't work break it and take it back for a refund ;)
This is not legal advice.
Posts: 3278
Joined: Mon Mar 03, 2003 9:03 pm
Location: St Helena, Melbourne.

Post by Loanrangie »

Whatever you use i find it easier to clamp a nice straight length of timber or steel tube to the sheetmetal and use it as a guide, i do this using a jigsaw on steel and wood and it means you get a nice straight cut.
Saddle up tonto, its the not so loanrangie! . 98 TDI DISCO lightly modded with more to come.
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest