who sells weld in cv joints for tailshafts

[cooter]

i want to fit one in the back shaft of my disco

[tuf045]

Hardy spicer or even maybe drivline services at bero

[cooter]

hardy wants 850 +fitting i have been told that the vz commodore runs one in the std shaft

[tuf045]

hardy wants 850 +fitting i have been told that the vz commodore runs one in the std shaft

Well there go's that theory. I don't personally know if the commodore runs one or not. Holden dealer maybe your freind go in and test drive one .

[Sic Lux]

If its what i'm thinking of yeah dunny doors have them just after the centre bearing think even back to vb model best bet if you were to use a 2nd hand one find a smahed vz so less worn out

[dumbdunce]

grab a few second hand 80/100/GU cv's and experiment? heat control will be the key, the only real drama you might have is finding a boot to suit that doesn't expand and/or shred at highway rpm.

could probably even use smaller/cheaper CV's, tailshaft torque will only be 1/3 - 1/4 axle torque.

[cooter]

i have heard of people using the front cvs out of ifs vehichle

[sierrajim]

grab a few second hand 80/100/GU cv's and experiment? heat control will be the key, the only real drama you might have is finding a boot to suit that doesn't expand and/or shred at highway rpm.

could probably even use smaller/cheaper CV's, tailshaft torque will only be 1/3 - 1/4 axle torque.

The boot on a tailshaft CV will be doing far less RPM than a FWD CV boot. Didn't the company that makes the drilled greasable CV make a CV boot for late 70 series CV's?

Mal's bushrangie runs 100 series CV's in the shafts. I was told by the guy that made them that he drilled out the flange so that the CV would be a press fit, pressed in the CV, welded it up, left it to cool naturally and they're still going.

Two other options, www.yuri4x4.com or Dobbin Engineering

[dumbdunce]

grab a few second hand 80/100/GU cv's and experiment? heat control will be the key, the only real drama you might have is finding a boot to suit that doesn't expand and/or shred at highway rpm.

could probably even use smaller/cheaper CV's, tailshaft torque will only be 1/3 - 1/4 axle torque.

The boot on a tailshaft CV will be doing far less RPM than a FWD CV boot. Didn't the company that makes the drilled greasable CV make a CV boot for late 70 series CV's?

bzzt a tailshaft CV in a 4WD will spin at least twice as fast and more like 3 - 4 times faster than a front wheel drive CV.

Mal's bushrangie runs 100 series CV's in the shafts. I was told by the guy that made them that he drilled out the flange so that the CV would be a press fit, pressed in the CV, welded it up, left it to cool naturally and they're still going.

Two other options, www.yuri4x4.com or Dobbin Engineering

I like the booty 100 series option. got me thinking about doing the front on my 80

[frp88]

Go and get a second hand dunnydore one and mod it it's not that hard

[rustys]

Dobbin makes them and we run them on Glen's, Pete's and Phill Nobles Trucks all with 44" plus tyres ,strong but not much good for hyway driving if you run them to much angle as heat is a problem.Boots are easy to get but speak to Glen he can make you a shaft any length for about $800 complete bolt in


Garth

[cooter]

i want to run it at an angle on highway what sort of life could be expected

[revin]

Have you also tried Gibsons out at Edgeworth.

He did the shaft in my old Hilux and was very good to deal with

[MART]

Cooter , I have tried to run a rear cv about ten times in my zuk , I used a 1.3 suzuki cv and parted of the stub axle , then left just enough to weld a standard zuk flange on , one I cut off a standard tailshaft , then welded it to the bell. The main problem is heat as they spin up to five times the speed they where meant to , so they will get hot spots where the ball bearings contact the bell of the cv. This will cause it to be notchy and become loose. Also the boots will shred as the grease melts it runs out and the centrifigal force breaks the boot and the extra heat doesn't help. I managed to find some boots via Garth and Glen which did the job but I could only grease the bell only which isn't much grease. This stopped the boots breaking but Istill had the overheating problem. I ended up angling my transfer case sideways in the car and down at the rear. This fixed my tailshaft angle problem and I know run uni's. I still have my front cv as when angled down at the rear the front uni could not cope with the angle so it is a cv and has no problem. All the guys run cv's in there comp cars but there comp cars don't do 110 down the freeway for hours on end. The commodores might run a cv in there shaft but the angle wouldn't be much and the final drive ratio would be nothing like a 4wd , but if you wanted to you can run any cv you want as stated there is not as much pressure on the tailshaft compared to axles , Just m2c , Cheers Paul.

[cooter]

i might give it a go and use my old shaft is there any reason ya cant run a tailshaft backwards?

[dumbdunce]

i might give it a go and use my old shaft is there any reason ya cant run a tailshaft backwards?

as long as the flanges are the same, go for it.

[cooter]

they will be

[Shadow]

they will be

I think the slipjoint is meant to face down to stop water etc running into it

but for a 4wd, where your going to sit in mud and water anyway, i doubt it will matter at all.

[Matt N]

What about Porsche CV boots?? Any good??
http://hunterrivmasta.com.au/products/P ... m?pcatid=3

[frp88]

Some of the old landrovers had a fabric that was wax filled to stop the grease from coming out.We use high pressure grease for our wire rolling machines I have in my cruser for at least 1and half years it great.

[NJV6]

I don't know if this is of any help or not......... but a SWB Pajero comes with a CV in the rear driveline. It is only on 3.5 litre V6 or 2.8 litre Tdi



NJ

[eXc]

GIBSON CV'S & TAILSHAFT SPARES

Edgeworth

http://www.netpostcode.com/nsw/nsw-g1/nsw-0595.html

[`maddog]

Glen Dobbin has the CVs with flanges welded onto them, off the shelf. As Garth has said, they're no good for highway use though. Depends what you're after.

I use Glen's gear in my rear tailshaft.

[bru21]

fill them with oil not grease, that way they won't get as hot. keeping it in there may be a problem though.

Also cv's are exactly that constant velosity, so ideally you have no angle on the uni as the steeper the angle gets the more the speed changes during rotation.

also depending on the application i would be careful with failure. Nothing is more annoying than something like this letting go.

What about patrol double cardian tailshafts from the front of leaf sprung utes. I bought one for $100

cheers bru