I am looking around for a u bolt flip kit for my cruiser - the standard setup just gets hung up in mud all the time.
I know snake racing does a kit and superior do a bolt on kit for the rear only - anybody else?
The Micheles Sacks troopy had it done (the write up is in one of the 4wd monthlies from about a year or so back) but I dont have the mag handy to see where it was done.
Anybody done this on their 75? Comments good or bad?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
75 series u bolt flip kits
Moderators: toaddog, Elmo, DUDELUX
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
i used a set of modified mounting plates that brings the bolt ends up beside the spring packs. I got them from superior for about the same as a flip kit. I'm not really convinced about the capacity of a flip kit to properly locate the axle. I was regularly pretzeling my bolts but since then i've not done one.
http://www.populationparty.org.au/
Superior do a kit for the front but they suggest that you use shock hoops so that you will still have the full travel of your shock, cause the problem is that the shock is attached to the u-bolt plate so you have to weld shock brackets to the back of your diff housing.
Correct me if iam wrong cause iam no expert on this but you will lose 1-2"inch down travel in your shock by moving it up if that makes sence.
But superior do have a new design and kit have a look hope i didnt confuse you mate somebody maybe able to explain it a bit better then me but hears the link for the new kit...
Cheers Azza
http://www.superiorengineering.com.au/p ... ts_id=2465
Correct me if iam wrong cause iam no expert on this but you will lose 1-2"inch down travel in your shock by moving it up if that makes sence.
But superior do have a new design and kit have a look hope i didnt confuse you mate somebody maybe able to explain it a bit better then me but hears the link for the new kit...
Cheers Azza
http://www.superiorengineering.com.au/p ... ts_id=2465
Other option .
http://www.man-a-fre.com/parts_accessor ... lipkit.htm
Keep the same lenght for your shocks ..
http://www.man-a-fre.com/parts_accessor ... lipkit.htm
Keep the same lenght for your shocks ..
HJ-60 2H-T Intercoled [url=http://4x4panama.com/foros/viewtopic.php?t=2770]Tencha[/url]
HDJ-80 1HD-T Stock so far " Marilu "
Panama
HDJ-80 1HD-T Stock so far " Marilu "
Panama
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
that man a fre is the go. Much better engineering solution.
while i havn't had any real dramas with my superior plates, they have two main drawbacks
1. the ubolts on the front have to be splayed out makes them a pain to get in the holes.
2. the loading on the side plates from u-bolts being 5-10mm out from the side of the spring pack puts leverage moment on them. So if you torque up the nuts like you are supposed to you can see them flexing as well as putting a lot of stress on the welded gussets under them. If those gussets were to fail and crack it could be catastrophic at speed. (i.e. axles moving longitudinally along the spring)
while i havn't had any real dramas with my superior plates, they have two main drawbacks
1. the ubolts on the front have to be splayed out makes them a pain to get in the holes.
2. the loading on the side plates from u-bolts being 5-10mm out from the side of the spring pack puts leverage moment on them. So if you torque up the nuts like you are supposed to you can see them flexing as well as putting a lot of stress on the welded gussets under them. If those gussets were to fail and crack it could be catastrophic at speed. (i.e. axles moving longitudinally along the spring)
http://www.populationparty.org.au/
Flip kit
Mate when u say your getting hung up on them, hows your truck set up?
What size tyres u running what spring lift body lift etc?
What size tyres u running what spring lift body lift etc?
R.I.P SILVER BULLET.
TOW RIG D4D 2011 LUX ON 33s. COMP RIG 95 SIGLE CAB LUX
SPONSORS EASTCOAST 4WD EASTSIDE AUTO KAR PRO TYRE AND AUTO
TECH ENGINEERING
TOW RIG D4D 2011 LUX ON 33s. COMP RIG 95 SIGLE CAB LUX
SPONSORS EASTCOAST 4WD EASTSIDE AUTO KAR PRO TYRE AND AUTO
TECH ENGINEERING
Who is online
Users browsing this forum: No registered users and 12 guests