Heres a Question guys ,
The gearbox output shaft on rovers , the shaft that fits from the gearbox into the transfer , Is the spline on this shaft 10 spline ?
It wouldn't be the same size and spline as a ten spline axle would it ?
are they all the same , ?
Thanks.
Larry.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Gearbox Output spline.
Moderator: Micka
mmmmm , Thought i would get a quick response here mmmm,
I havn,t got a RR box lR box or transfer , and just want to know is the input to the transfers the same on RR and LR case although the t?cases are different ,
I have seen only one pic it was of a reworked T18 box being setup for a LR transfer , It had a reworked rear output to match the LR transfer it looked to be of only course ten spline ?
Its all to do with a possible th180 to lt230 , I would need to have the rear output machined or a spud shaft biult , not keen on spuds , so If i get the measurements of the input diameter i will know if there is enough meat on the th180 output to have it reworked to siut Lt230.
Are the transfers of the same strength LR P/T RR f/t
Won,t need F/t as will be Nis diffs with Freewheel hubs but if case is stronger , Does anyone have T case in bits , wouldn't mind knowing the gear phisycal size , width of the actual gears , diameter ect To compare with my other transfers i already have , MQ detached , Any info Greatly appreciated
Thanks guys
Larry
I havn,t got a RR box lR box or transfer , and just want to know is the input to the transfers the same on RR and LR case although the t?cases are different ,
I have seen only one pic it was of a reworked T18 box being setup for a LR transfer , It had a reworked rear output to match the LR transfer it looked to be of only course ten spline ?
Its all to do with a possible th180 to lt230 , I would need to have the rear output machined or a spud shaft biult , not keen on spuds , so If i get the measurements of the input diameter i will know if there is enough meat on the th180 output to have it reworked to siut Lt230.
Are the transfers of the same strength LR P/T RR f/t
Won,t need F/t as will be Nis diffs with Freewheel hubs but if case is stronger , Does anyone have T case in bits , wouldn't mind knowing the gear phisycal size , width of the actual gears , diameter ect To compare with my other transfers i already have , MQ detached , Any info Greatly appreciated
Thanks guys
Larry
I have my Defender LT 230 apart on the bench at the momet. Don't know if any of the measurements are the same as RR, but let me know if you want some more.
Output shaft - 10 spline - OD 30mm - ID (bottom of splines) 26.4mm
Axle - 10 spline - OD 28mm - ID (bottom of splines) 25.4mm
Daryl
Output shaft - 10 spline - OD 30mm - ID (bottom of splines) 26.4mm
Axle - 10 spline - OD 28mm - ID (bottom of splines) 25.4mm
Daryl
Daryl Snowdon
Melbourne Australia
1954 86" Series 1 Hardtop - 'under construction'
1993 110" Defender Hardtop
Melbourne Australia
1954 86" Series 1 Hardtop - 'under construction'
1993 110" Defender Hardtop
Who is online
Users browsing this forum: No registered users and 14 guests