I have just fitted a oil pressure gauge to the beast and have found that the oil pressure is a little low as it's down to 28-30 psi at 2500rpm at opperating temp as it's ment to be 40psi min apparently.
Is it hard to rebuild/reco these as the rest of the motor seem okay (except for maybe the heads) or does any one on here have a good one for a 3.9efi engine number with out suffix B.
Trav
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Oil Pump
Moderator: Micka
Can you do that while it's still on the car ??bigbad wrote:just take the cover off the pump and drop the gears out, replace the gears, check the cover for wear and pack it with vaseline to prime it, fit cover, job done. It could be the pressure relief spring that is causing the lower pressure, so may be worth replacing that first.
Trav
'91' Dual Cab Hilux
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
HPR 15 is way to light for it HPR 30 or HPR 50 is the go i use 50 in mine but its had a long hard life ...
As for the oil pump most good landy shops sell a reco kit for em with new gears and springs and gaskets i think the kit is around the 90 buck mark
As for the oil pump most good landy shops sell a reco kit for em with new gears and springs and gaskets i think the kit is around the 90 buck mark
Cheers
Chris
Questions $20ea Answers for said Questions $100ea
I can fix your F'ups for a fee .......
Chris
Questions $20ea Answers for said Questions $100ea
I can fix your F'ups for a fee .......
I was told that the HPR 15 is whats recomended for it but I'll try some HPR 30 as some thicker oil might help as she has done about 290,000k'slokka wrote:HPR 15 is way to light for it HPR 30 or HPR 50 is the go i use 50 in mine but its had a long hard life ...
As for the oil pump most good landy shops sell a reco kit for em with new gears and springs and gaskets i think the kit is around the 90 buck mark
Trav
'91' Dual Cab Hilux
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
Well I put some HPR40 (25w-70) in and the pressure only incresced to about 32-35psi so I'm going to do the pump but I have been told that the main and/or bigends are worn and they might need replacing as well as the motor has done nearly 300000k's.
To do the oil pump do I need to remove it from the motor or can I do the gears and releif spring while it's still on the car ??
Trav
To do the oil pump do I need to remove it from the motor or can I do the gears and releif spring while it's still on the car ??
Trav
'91' Dual Cab Hilux
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
If it was a manual, I had an 81 in saudi which had more than that. You could clunk it backwards and forwards.
However all the rest of the bearings were relatively OK. I put it down to pushing the clutch in.
However, the centre bearing has the thrust washers integral so I had to have the crank ground undersize. This was in Saudi, where noone knew anything. Maybe in NZ you could get oversize thrust washers separate from the bearing.
Regards Philip A
However all the rest of the bearings were relatively OK. I put it down to pushing the clutch in.
However, the centre bearing has the thrust washers integral so I had to have the crank ground undersize. This was in Saudi, where noone knew anything. Maybe in NZ you could get oversize thrust washers separate from the bearing.
Regards Philip A
One of the reasons I bought the gauge was because the oil light was coming on and off all the time at no set intervils and yes it is a mechanical gauge and the pressure sits steady.armbrup wrote:Just a thought.
Why not try a mechanical gauge directly connected to the pressure switch mount, to check whether your gauge is reading correctly.
Most mechanics have them.
300K is lot though.
I bet you never worried before you bought that damn gauge.
Regards Philip A
Trav
Last edited by Nice_Surf on Tue Feb 19, 2008 4:55 pm, edited 1 time in total.
'91' Dual Cab Hilux
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
'07' Suzuki GSX1400
'82' Suzuki PE250Z
What more do I need
One of the reasons I bought the gauge was because the oil light was coming on and off all the time at no set intervils and yes it is a mechanical gauge and the pressure sits steady.
When mine died in Saudi, it was because the oil light was coming on up to about 1500RPM. I rebuilt the engine with all new bearings, and guess what , the oil light still came on.
A new sender fixed it. Maybe buy a new sender and see if it makes a difference to the light coming on.
I am suggesting that you borrow ANOTHER mechanics type gauge to check whether your gauge is correct. An engine would really have to be bad to not make pressure at 2500RPM with 70 in it. You should hear the big ends a clonkin.
Regards Philip A
Who is online
Users browsing this forum: No registered users and 3 guests