Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Help with Jaycar Dual Batt Kit
Moderator: -Scott-
Help with Jaycar Dual Batt Kit
I've taken the jaycar kit out of my old fourby and installed into the triton. The problem is I've stuffed up the wiring somehow as I cant get it to work. It was working fine before!! Can anyone who's got one explain which wire goes where? Cheers.
Can you post which wires you have (including colours?) and where you have them connected?
From memory, I have the two main leads, an earth wire, a second (blue?) wire connected to the primary battery (voltage sense for the primary battery - tells the controller the primary battery voltage, unaffected by voltage drop on the main charge lead) and an orange wire providing an "engine running" signal.
From memory, I have the two main leads, an earth wire, a second (blue?) wire connected to the primary battery (voltage sense for the primary battery - tells the controller the primary battery voltage, unaffected by voltage drop on the main charge lead) and an orange wire providing an "engine running" signal.
Jaycar CAN NOT re-issue plans/instructions as they are often owned by a third party (silicon chip Magazine)
Jaycar have a forum, jump on there, somebody will know
https://secure.vividcluster.crox.net.au ... /forum.asp
Jaycar have a forum, jump on there, somebody will know
https://secure.vividcluster.crox.net.au ... /forum.asp
Last edited by fool_injected on Wed Jun 11, 2008 4:24 pm, edited 1 time in total.
[url=http://www.4x4masters.com.au/]Australian 4X4 Masters Series website[/url]
non illegitimi carborundum!
[url=http://www.suzuki4wd.com.au/forum/]Suzuki 4wd Club of NSW forum[/url]
non illegitimi carborundum!
[url=http://www.suzuki4wd.com.au/forum/]Suzuki 4wd Club of NSW forum[/url]
I had one of the $99 Jaycar jobs and it did work.........as in isolating one of the batteries so both didn't go flat.
In my case I left the lights on and flattened the main cranking battery. Simple jump start next morn from 2nd battery.
From memory there is just an earth, pos feed in from alt and pos feed out x2, (1 for each batt).
Always had problem with low voltage (as in just below normal on RRC voltmeter) at night with lights, wipers, heater fan, stereo and thermo fan going. Knew I was losing about 0.5 v from alt with the Jaycar unit. Thought about 2nd alt, etc.
Bought a Redarc isolator on impulse and fitted it. Now runs all the above stuff without slipping out of the 'normal' range on the voltmeter. Made a big difference, but did not measure before and after. Just going on the difference on the gauge.
In my case I left the lights on and flattened the main cranking battery. Simple jump start next morn from 2nd battery.
From memory there is just an earth, pos feed in from alt and pos feed out x2, (1 for each batt).
Always had problem with low voltage (as in just below normal on RRC voltmeter) at night with lights, wipers, heater fan, stereo and thermo fan going. Knew I was losing about 0.5 v from alt with the Jaycar unit. Thought about 2nd alt, etc.
Bought a Redarc isolator on impulse and fitted it. Now runs all the above stuff without slipping out of the 'normal' range on the voltmeter. Made a big difference, but did not measure before and after. Just going on the difference on the gauge.
Who is online
Users browsing this forum: No registered users and 9 guests