torno covers????

Post by **Macca177** » Tue Mar 16, 2004 7:14 pm

ok where's the best palce to get them made up?
a 4wd shop or is there specialzed shops?
also should i get it b4 the roll bars or after ?

its for a single cab lux so im gussin round $300 would be wot they are worth ?
am i near in $$?

Post by **ozy1** » Tue Mar 16, 2004 7:49 pm

Id get it after the bars, as they will be able to make it look like a neater fit!

Post by **tuff 45** » Tue Mar 16, 2004 8:41 pm

ozy1 wrote:Id get it after the bars, as they will be able to make it look like a neater fit!

D and D Autotrim do a good job, they are at South Windsor. Do the roll bar's first.

Post by **taziiy** » Tue Mar 16, 2004 8:59 pm

any motor trimmer should be able to do it but its just a matter of shopping around for best price after the bar work

Post by **ToNkA** » Tue Mar 16, 2004 9:03 pm

I got mine done for $300 from a local auto trimmer.

Got it cut to fit the Roll Bar and had two bar supports and clips put around the tray.

Post by **80UTE** » Wed Mar 17, 2004 8:17 am

I got a new one 2 months ago for my hilux twincab from a Toyota dealer and i cost me about $185.00

Website · Post by **XXXL80** » Wed Mar 17, 2004 8:37 am

give nans tarps a call at lidome.

really good service and great price.

Post by **98lux** » Wed Mar 17, 2004 1:55 pm

80UTE wrote:I got a new one 2 months ago for my hilux twincab from a Toyota dealer and i cost me about $185.00

$180 for mine with fitting kit, and $50 for rollbar mods

Post by **roadrunner** » Wed Mar 17, 2004 2:19 pm

There's a bloke on the road out to Shark Park ( turning off Taren Point Rd) who made one up for my Landcruiser. Top job and is more than willing to put the effort in to make sure you get what you want. Its a custom trim place but he does boat and ute stuff too.

Buggered if I can remember the name though

Post by **Shorty40** » Wed Mar 17, 2004 2:22 pm

roadrunner wrote:There's a bloke on the road out to Shark Park ( turning off Taren Point Rd) who made one up for my Landcruiser. Top job and is more than willing to put the effort in to make sure you get what you want. Its a custom trim place but he does boat and ute stuff too.

Buggered if I can remember the name though

Is it near the boat accessory place, just past the lights ?

If so I can find out the name tonight, I drive past there on the way to and from work.

Post by **roadrunner** » Wed Mar 17, 2004 4:45 pm

Shorty40 wrote:
roadrunner wrote:There's a bloke on the road out to Shark Park ( turning off Taren Point Rd) who made one up for my Landcruiser. Top job and is more than willing to put the effort in to make sure you get what you want. Its a custom trim place but he does boat and ute stuff too.

Buggered if I can remember the name though

Is it near the boat accessory place, just past the lights ?

If so I can find out the name tonight, I drive past there on the way to and from work.

Yeah, could be the place. Its just after the lights heading for the footy oval. There's was an old servo at the lights. The servo and the trimmer dude will be on your left as you head to Kurnell.

Post by **Macca177** » Wed Mar 17, 2004 4:55 pm

thanks all ... is it near or close to battery world ?

soudns good!
will get bars 1st then

thanks all again

Post by **roadrunner** » Wed Mar 17, 2004 6:23 pm

Macca177, its just around the corner from Battery World.

Definitely get your bar work done first, but an idea may be to have the cover made with velcro patches over where the bar comes through just in case you decide to remove the bar later.

Saves you getting another cover made up

Outer Limits 4x4 Board

torno covers????

torno covers????

Who is online