Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

3rd Cylinder Problems

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 20
Joined: Thu Oct 30, 2003 2:04 pm
Location: Bathurst

3rd Cylinder Problems

Post by Courtancer »

I've narrowed a running rough problem down to the 3rd cylinder. When I pull the lead off the spark plug while its running, there is not much noticeable difference. If I pull the lead off any of the other plugs, you can hear a definate difference. I've tested the spark plug and the lead and replaced the plugs, distributer cap and points not long ago. What could be the problem with the cylinder and how can I fix it?
No Signature
Top
Posts: 115
Joined: Tue Oct 21, 2003 5:27 pm
Location: Sydney

Post by No Idea »

Compression test it. If there is no comp or very low, it could be a valve, either bent/not seating properly or cracked. If there is comp do a wet test and see if it improves the pressure (wet meaning put a few squirts of oil in the plug hole and re-test). if the comp does improve, that will determine that it is a ring problem.
Top
Posts: 125
Joined: Sun Nov 23, 2003 4:54 am
Location: Seattle, Washington

Post by mtzook »

Defective wires are very common. They get bent sometimes too tight in their packaging, or before you buy them, and that can damage their insides.

Swap out that wire with another one, and see if there's any difference.

I had a 1.3L with the 3rd cyl. compression low. I sold it, so i didn't end up fixing it...
My tires were rubbing in the front, so I trimmed the hood, and now they're fine...
Top
Posts: 20
Joined: Thu Oct 30, 2003 2:04 pm
Location: Bathurst

Post by Courtancer »

I tried a different lead but still had the same problem. Would it be worth trying any of the oil additives to clean the valves or seal leaks, etc?
No Signature
Top
Posts: 125
Joined: Sun Nov 23, 2003 4:54 am
Location: Seattle, Washington

Post by mtzook »

shoot a butt load of carby cleaner down there and maybe knock off some carbon deposits on the valves. Maybe the valves aren't seating right from too much crap. It's worked well for me before on a V8 Jaguar engine.

Oil additives can help increase compression, but it's only a temporary fix.

Did you test the compression yet?? From memory, i think they're supposed to have 140psi, and the 3rd cylinder i had was 80psi.
My tires were rubbing in the front, so I trimmed the hood, and now they're fine...
Top
Posts: 20
Joined: Thu Oct 30, 2003 2:04 pm
Location: Bathurst

Post by Courtancer »

I haven't tested the compression yet. The tester I have is too short to get down into the hole. I'll have a go at giving it a good blast.
The problem isn't really noticeable at high speeds. Does that still sound like a valve problem?
No Signature
Top
Posts: 125
Joined: Sun Nov 23, 2003 4:54 am
Location: Seattle, Washington

Post by mtzook »

It's always hard to notice problems like that at high speed, especially in the loudest 4x4 ever created (sierra's).
My tires were rubbing in the front, so I trimmed the hood, and now they're fine...
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 7 guests