Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

HILUX REAR TAIL SHAFT

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 185
Joined: Sun Nov 18, 2007 3:03 pm
Location: deception bay

HILUX REAR TAIL SHAFT

Post by luxenberg »

Just got new thick wall one peice rear tail for my 94 d/cab hilux.I have noticed some photos on the internet some people are running them back to front(the slip yolk at the diff end.Is this just to gain a little better ground clearance near the diff?If so no problem running this way as a daily.
Steve
Top
Posts: 1451
Joined: Sat Mar 18, 2006 1:25 pm
Location: hilux is in NSW.. Im in WA again

Post by brad 93hilux »

not sure what others are doing but, mine has the slip yolk at the top side...

But i was worried about damaging the spline... but can imagine the other way would be better with water so water does not sit inside the spline.


Prob no help ;)

Brad
3.0L turbo diesel, 4" lift, bud's front housing, track assasin cv's, air lokker front + Rear, beadlock'd 37 stickies, high steer, 15.5" travel ranchos, high pinion diff and coils on the rear
Top
Posts: 6
Joined: Mon May 19, 2008 5:02 pm
Location: IPSWICH

Post by 1_tuff_sierra »

alot of guys are runing them back to front so they dont fill the shaft
up with mud water and the rest of it i run myn back to front but i am runing rhs rear shaft because i got sick of replacing round ones :) :lol: :)


hope this helps

tim
Top
Posts: 1650
Joined: Wed Jun 06, 2007 10:12 pm
Location: ipswich

Contact:
Contact sloshy

Post by sloshy »

I wouldn't run the slip joint at the diff end, it would get damaged to easy. As long as you keep grease in the slip joint it will keep the water and mud out. I got sick of bending them so I made mine with 65nb x 8mm wall.
cheers Dan

Licenced Carpenter
I do everything, free quotes
Brisbane west/Ipswich/rural
PM me
Top
Posts: 185
Joined: Sun Nov 18, 2007 3:03 pm
Location: deception bay

Post by luxenberg »

sloshy wrote:I wouldn't run the slip joint at the diff end, it would get damaged to easy. As long as you keep grease in the slip joint it will keep the water and mud out. I got sick of bending them so I made mine with 65nb x 8mm wall.
Hey Dan my 1 piece shaft is 4.5mm thick, they said that if they go any thicker they can'y balance it right for road use.Is your shaft round or square
and is it any good on the road.
Steve
Top
Posts: 6
Joined: Mon May 19, 2008 5:02 pm
Location: IPSWICH

Post by 1_tuff_sierra »

myn is square but i do not use my truck on the road but yet saying that i have had it up 2 140clicks down binnies rd and no vib or anything
Top
Posts: 1650
Joined: Wed Jun 06, 2007 10:12 pm
Location: ipswich

Contact:
Contact sloshy

Post by sloshy »

luxenberg wrote:Is your shaft round or square
and is it any good on the road.
Steve
Its tube, just turned the ends to suit and straightened it in the lathe, didn't balance it at all, but it is off road only, but in saying that I have had it at 100k's and its fine.


Can't see why they can't balance it though if you went bigger :?
cheers Dan

Licenced Carpenter
I do everything, free quotes
Brisbane west/Ipswich/rural
PM me
Top
Posts: 826
Joined: Mon Mar 20, 2006 1:08 pm
Location: Redcliffe

Post by berad »

Ur opinion is null and void, where were you sooky boy on the weekend haha
BBP Offroad
Boondall Backyard Performance

They call me the MR. throw cash at shiz til its comp specccccc
Top
Posts: 1650
Joined: Wed Jun 06, 2007 10:12 pm
Location: ipswich

Contact:
Contact sloshy

Post by sloshy »

berad wrote:Ur opinion is null and void, where were you sooky boy on the weekend haha
I did think about coming for about .3 of a second.
cheers Dan

Licenced Carpenter
I do everything, free quotes
Brisbane west/Ipswich/rural
PM me
Top
Posts: 826
Joined: Mon Mar 20, 2006 1:08 pm
Location: Redcliffe

Post by berad »

haha, u didnt miss out on much
BBP Offroad
Boondall Backyard Performance

They call me the MR. throw cash at shiz til its comp specccccc
Top
Posts: 1490
Joined: Thu Nov 28, 2002 12:53 pm
Location: Brisbane - D'Bay

Post by Willy Hilux »

I'm running 6.5mm wall thickness seamless pipe. Being seamless i should be pretty well balanced. But it is for off road only. I wouldn't run the spline at the diff end. Shit idea.
AMADAXTREME Racing
Sponsors-
AmadaXtreme
Superior Engineering
www.superiorengineering.com.au/
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 101 guests