Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Water.. How deep????

Tech Talk for Mitsubishi owners.

Moderator: -Scott-

Post Reply
Posts: 62
Joined: Mon Jun 28, 2010 4:53 am
Location: Budapest

Water.. How deep????

Post by 4x4boi »

Hello,

I have 3.0petrol LWB paj. Have a snorkel, winch, has a 2inch suspension lift and a 3inch body lift, also the motor has been also raised up to suit body lift. My question is how deep and i go in water??? My guess would be until i dont reach the generator right? or no?


Cheers
1994 3.0v6 auto, 2inch suspension, 3inch body lift, 4.5t winch, snorkel, roof rack, Factory locker,33x12.5x15 mud tyres, and lots of lights.
Posts: 90
Joined: Tue Oct 10, 2006 2:18 pm
Location: Brizvegas

Re: Water.. How deep????

Post by Mechz »

As long as the engine can breathe you'll be fine, just make sure your windows are up and your diff breathers are either plugged or extended so they don't suck water in.
92' NH Pajero SWB 3.0 V6
Posts: 1383
Joined: Tue May 06, 2008 8:12 pm
Location: Newcastle

Re: Water.. How deep????

Post by oldmate »

The theory is the bottom of the snorkel head, assuming the entire intake is sealed up until that point.

The 'safe' guideline is generally the top of the wheel rim.

Although after any water crossing you should check all oils for contamination, and regrease the driveshafts.
The worst part about being told you have Alzheimer's, is that it doesn't just happen once.
Posts: 62
Joined: Mon Jun 28, 2010 4:53 am
Location: Budapest

Re: Water.. How deep????

Post by 4x4boi »

Cheers for the reply fellas. Will today i gave it a go and the water was up to the top of the fenders, only problem i had was there was heaps of sand and that mosity crap and the front tyres sank in the frist time and couldnt go nowhere, Than i put it in diff lock and slowly it came out of the sandy part. On the way home the electronic shock absorder ( soft, medium, hard) switch was showing soft and than hard and it kept on blinking back and forth from soft to hard... after a few hours it stopped. So everything was ok, i think the paj could have gone threw pretty easy if there wasnt heaps of mosity sand :D

Cheers
1994 3.0v6 auto, 2inch suspension, 3inch body lift, 4.5t winch, snorkel, roof rack, Factory locker,33x12.5x15 mud tyres, and lots of lights.
Posts: 194
Joined: Sun May 11, 2008 12:30 am
Location: Manila, Philippines

Re: Water.. How deep????

Post by monmendoza »

my experience with water crossing is to avoid it as much as
possible. While your rig itself will normally be able to survive
up to more than the top wheel rim, eventually after a few
weeks your alternator will show sign of damage. After
damaging 2 alternators in 2 separate occasions, I decided
that crossing deep water is not much fun. :)
Posts: 32
Joined: Fri Jul 24, 2009 9:23 pm
Location: Italy

Re: Water.. How deep????

Post by fondente »

theoretically you can push until the suction nozzle is out of the water... For me you should also make waterproof electrical system... I've seen many times 3.0V6 (generally gasoline powered off road veichles) with electrical problems during or after a ford... Diesel ones are less sensible to water...
'96 gen2 2.8 TDI, 33", 4.9 gear ratio,front Arb rear stock locker, Air Flow snorkel, no sway bar

http://www.fondente.org
http://www.youtube.com/fondente71
http://picasaweb.google.com/fondente
Posts: 77
Joined: Wed Oct 13, 2010 8:50 am
Location: Little Green Ireland

Re: Water.. How deep????

Post by Chris_McCartney »

Factory figures say 60mm for the petrol and diesel SWB and LWBs, seems a bit inaccurate to me as the LWB has 2 inch taller suspension and the 2.5 Diesels dont have the factory 1.5inch body lift to fit the larger gearbox...sorry this was actually quite a useless post!!
Man: "What happened to the back of it?"
Me: "oh I dented the bumper on a post.."
Man: "No... where the hell is the roof?!"
Posts: 77
Joined: Wed Oct 13, 2010 8:50 am
Location: Little Green Ireland

Re: Water.. How deep????

Post by Chris_McCartney »

Sorry 60cm
Man: "What happened to the back of it?"
Me: "oh I dented the bumper on a post.."
Man: "No... where the hell is the roof?!"
Posts: 36
Joined: Fri Jun 04, 2010 10:03 am
Location: cairns

Re: Water.. How deep????

Post by deepdiverdave »

fondente wrote:theoretically you can push until the suction nozzle is out of the water... For me you should also make waterproof electrical system... I've seen many times 3.0V6 (generally gasoline powered off road veichles) with electrical problems during or after a ford... Diesel ones are less sensible to water...
iv had the diesel mj triton and now iv got the petrol and have problems with water crossings that are only half as deep as what i used to go through with the diesel.
something keeps shorting out and blowing fuses :cry: the first time it happened i was only half way across and on my own had to drive it out on the starter motor in 1st gear.
got any advice on how to water proof my wireing???????????
Posts: 490
Joined: Wed Mar 10, 2010 10:36 am
Location: Endeavour Hills, VIC

Re: Water.. How deep????

Post by tehekho »

deepdiverdave wrote:
fondente wrote:theoretically you can push until the suction nozzle is out of the water... For me you should also make waterproof electrical system... I've seen many times 3.0V6 (generally gasoline powered off road veichles) with electrical problems during or after a ford... Diesel ones are less sensible to water...
iv had the diesel mj triton and now iv got the petrol and have problems with water crossings that are only half as deep as what i used to go through with the diesel.
something keeps shorting out and blowing fuses :cry: the first time it happened i was only half way across and on my own had to drive it out on the starter motor in 1st gear.
got any advice on how to water proof my wireing???????????
Cover it in RTV :armsup:
ferog wrote:I've had worse smelling fingers though.
Posts: 36
Joined: Fri Jun 04, 2010 10:03 am
Location: cairns

Re: Water.. How deep????

Post by deepdiverdave »

??? might look stupid here but what is rtv?
Posts: 490
Joined: Wed Mar 10, 2010 10:36 am
Location: Endeavour Hills, VIC

Re: Water.. How deep????

Post by tehekho »

deepdiverdave wrote:??? might look stupid here but what is rtv?
http://lmgtfy.com/?q=rtv" onclick="window.open(this.href);return false;

Its a silicone based sealant....
ferog wrote:I've had worse smelling fingers though.
Posts: 36
Joined: Fri Jun 04, 2010 10:03 am
Location: cairns

Re: Water.. How deep????

Post by deepdiverdave »

looks like good stuff :armsup: where can i get it :?:
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest