Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
80 rear diff
Moderators: toaddog, Elmo, DUDELUX
80 rear diff
I own a 80 series 4.5 petrol landcruiser. I have recently put a turbo on it and am pushing 250 RWKW. Since i have done this i am constantly shearing bolts off the rear hub. Have had changed to unbrako's and also removed both dowell pins and replaced with unbrako bolts also. Can anyone please give advice on what to do as an upgrade. Was possibly thinking of GQ or GU nissan rear diff, customised using parts from both diffs being 80 series and nissan parts????? Can this be done and engeneered?????
Re: 80 rear diff
80WEPN wrote:I own a 80 series 4.5 petrol landcruiser. I have recently put a turbo on it and am pushing 250 RWKW. Since i have done this i am constantly shearing bolts off the rear hub. Have had changed to unbrako's and also removed both dowell pins and replaced with unbrako bolts also. Can anyone please give advice on what to do as an upgrade. Was possibly thinking of GQ or GU nissan rear diff, customised using parts from both diffs being 80 series and nissan parts????? Can this be done and engeneered?????
Still running stock axles?
Re: 80 rear diff
redrill and tap the hubs and axle flanges for 10mm bolts and dowells
RN wrote:pussy is out, its the log for me... Thank you Jesus.
Re: 80 rear diff
i used the dowells from the 100# cruiser and then used 45mm long socket head cap screws with a 10mm clear shank on the bolt and use a 8mm allen key and have not broken one yet running rear locked on 39" tyres also i dont use the cone washers either
toyota 80#,d/cab ute chop,6" springs,20mm body lift, 315/75/16 muds, and 39" michelin XML play tyres , turbo 4.2 1HZ top mount intercooler diesel.now ENGINEERED.
Reece
Reece
Re: 80 rear diff
throw a whole new gu trol diff in, make sure ratios are right, prob solved
Re: 80 rear diff
Except a GU diff wont fit and probably wont be any stronger overall.
Replace all the studs with the 100's equivalent which are 10mm VS 80 series 8mm
Replace all the studs with the 100's equivalent which are 10mm VS 80 series 8mm
The Silver Bullet - BJ74
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Re: 80 rear diff
yes still running standed axles but they are not the prob. i have been told not to drill out to 10mm besause you dont end up with bugger all steel left on out side of hub
MUD80D
any chance of a bit more detail.
MUD80D
any chance of a bit more detail.
Re: 80 rear diff
It will be fine. Changed to ten mm years ago, but use socket head bolts instead of studs and have never had a problem.80WEPN wrote:yes still running standed axles but they are not the prob. i have been told not to drill out to 10mm besause you dont end up with bugger all steel left on out side of hub
MUD80D
any chance of a bit more detail.
80 xtra cab
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Re: 80 rear diff
Another thing, have u checked ur wheel bearings lately.? Loose bearings will snap studs no matter how good they are .
80 xtra cab
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Re: 80 rear diff
80WEPN wrote:yes still running standed axles but they are not the prob. i have been told not to drill out to 10mm besause you dont end up with bugger all steel left on out side of hub
MUD80D
any chance of a bit more detail.
If your not snapping the STD axles with 8 Unbrako (Grade 12) bolts then your problem probably isnt the added HP. You could either have a bent housing or a wheel bearing issue. If it was HP related then the grade 12 bolts should hold up and the axles should twist off at the spline.
Re: 80 rear diff
had the same problem, i replaced the 8mm dowels with 10mm ones , and drilled two more positions ,(4 dowels) still running 8mm studs, haven't had any more problems.
running air lockers, standard 4.2 diesel ,and 35"simex .
running air lockers, standard 4.2 diesel ,and 35"simex .
Re: 80 rear diff
Here is a bolt in solution, run ARP studs.
http://frontrangeoffroadfab.com/nfoscom ... 0b1221b201" onclick="window.open(this.href);return false;
http://frontrangeoffroadfab.com/nfoscom ... 0b1221b201" onclick="window.open(this.href);return false;
Link Suspension Systems for your 79-95 hilux or 4Runner.
http://www.4wheelunderground.com" onclick="window.open(this.href);return false;
THE BEATINGS WILL CONTINUE UNTIL MORALE IMPROVES
http://www.4wheelunderground.com" onclick="window.open(this.href);return false;
THE BEATINGS WILL CONTINUE UNTIL MORALE IMPROVES
Who is online
Users browsing this forum: No registered users and 59 guests