Atempted to replace water pump, thermostat and bottom housing o ring on my td42 89 on the weekend.
Snapped 3 bolts one at back off thermostat the long one and two on top going into the head. So 2 broken bolts holding on horizontal and one verticle made for a good ol time. Anyhow snapped a plastic fitting coming out of thermostat housing sqaure fitting , i thought it was temp sender but i located one on ebay and its the round fitting below the one i broke. So what did i break ?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
F@#$ing Thermostat housing whats this thing
F@#$ing Thermostat housing whats this thing
If i just overtook you head to your nearest mechanic
Posts: 73
Joined: Fri May 09, 2008 7:01 pm
Joined: Fri May 09, 2008 7:01 pm
Location: Brisbane, QLD, Australia, Earth, 3rd Rock From The Sun.
Re: F@#$ing Thermostat housing whats this thing
post a pic champ, it will make it a lot easier for people to help you
Re: F@#$ing Thermostat housing whats this thing
that will be the temp sensor for the glowplug timer.
The dreaded long bolt strikes again. Been bitten a couple of times by that one.
Buy yourself a helocoil / recloil kit. and grease the thermostat bolts EVERY time.
The dreaded long bolt strikes again. Been bitten a couple of times by that one.
Buy yourself a helocoil / recloil kit. and grease the thermostat bolts EVERY time.
Re: F@#$ing Thermostat housing whats this thing
got the long one out with pliers only siezed in housing ezy out got the other 2 . ran a tap through all holes and will antisieze everything
Thanks for the reply mike will the car start without the glow sensor, i will order one but prolly wont get here this week
Thanks for the reply mike will the car start without the glow sensor, i will order one but prolly wont get here this week
If i just overtook you head to your nearest mechanic
Re: F@#$ing Thermostat housing whats this thing
Dunno if it will start, you would THINK that Nissan would make it reasonably fail safe.
Metal based anti seize may make it worse... its brass bits screwed into aluminium so its already an electrolytic corrosion issue. I use a bit of loctite hydraulic sealant and that is all on tings like that.
Metal based anti seize may make it worse... its brass bits screwed into aluminium so its already an electrolytic corrosion issue. I use a bit of loctite hydraulic sealant and that is all on tings like that.
Re: F@#$ing Thermostat housing whats this thing
yep ..never use "copper never seize" it makes it worse.......use the graphite based stuff
GQ with 30 PSI of TD42T.........
Re: F@#$ing Thermostat housing whats this thing
The car will start without the temp sender for the glow plugs but the glow plugs won't work so it will be hard to start and you'll get a massive belch of smoke out of it when it finally kicks over. Doesn't hurt it but just make sure that you let it run long enough to warm up properly so that it burns off most of the soot. It will clag up your injectors over a long time if not sorted properly.
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346j-top paj wrote:gayer than jizz on a beard
Re: F@#$ing Thermostat housing whats this thing
bit old but i'm pretty sure you can manualy glow gq plugs., same as mq/k hold the key half way between on and start, and it should kick the glow relay in.
Who is online
Users browsing this forum: No registered users and 46 guests