Outer Limits 4x4 Board

sick of always bending control arms went to overkill and got sam to sort out a 4 link for my junk

onrd handling is awesum and another think it squats under acceleration instead of lifting passengers side


while we were at it we moved the diff back 1 inch and i got keen with the air hacksaw.pics to come verry soon

just need to move shock mounts to get it flexin thou i am gunna do that after the front if 4 linked

verry happy so far

sounds sweet when ya comin down to try it

have to come soon mate also got a rear bar thou i needs some modds

This setup will be available as a kit and we are currently making a kit to replace the fornt arms as well
SAM

now for the pics

pics will be up tomorrow arvo

Are you going triangulated 4 link in the front if not what are you going to fit?

duncan wrote:Are you going triangulated 4 link in the front if not what are you going to fit?

it wont be a trianglated 4 link (daily driven rig) it will just be the same as the rear 3 straight links with panhard

i belive ruff runs this setup on the front of his green buggy and likes it (ruff only has power steer so still has a draglink)

OVERKILL ENGINEERING wrote:This setup will be available as a kit and we are currently making a kit to replace the fornt arms as well
SAM

now for the pics

At what sort of cost

HRZOOK (potential customer)

can't have rb zook out driving my rig, although he does already

HRZOOK wrote:

OVERKILL ENGINEERING wrote:This setup will be available as a kit and we are currently making a kit to replace the fornt arms as well
SAM

now for the pics

At what sort of cost

HRZOOK (potential customer)

can't have rb zook out driving my rig, although he does already

$1250
SAM

OVERKILL ENGINEERING wrote:

HRZOOK wrote:

OVERKILL ENGINEERING wrote:This setup will be available as a kit and we are currently making a kit to replace the fornt arms as well
SAM

now for the pics

At what sort of cost

HRZOOK (potential customer)

can't have rb zook out driving my rig, although he does already

$1250
SAM

Ok is that fitted?

Can this kit be purchased as a DIY project and if so cost?

Cheers
HRZOOK

Supply only can be done your self
SAM

Ok so whats in the "KIT"

PICS god dam it

HRZOOK

HRZOOK wrote:Ok so whats in the "KIT"

PICS god dam it

HRZOOK

i have his digi so he cant get pics yet

gotta see, gotta see

here can sort of see it

and yess i kept drivin from there and got on the loud pedal on that ledge the rear hust squated and drove it was luvin it


will get pics tomorrow in daylight

duncan wrote:Are you going triangulated 4 link in the front if not what are you going to fit?

The front will be very similar to our coil kit which is a three link as Tim stated
SAM

i got the shits when this hapened all the time

flexed nice this arvo at menai

few flex shots

nice flex looks like it works well.

roc box wrote:nice flex looks like it works well.

thanks.

just need to save my coin and get the front workin like that.

also need coil retainers

looks sweet nice rear bar too

yeah rear bar has to be lifted thou fukin body lift

Grimace Ryan, very very Grimace

but lookin good

poser shots....

Forgive me if I am wrong but This four link looks pretty much the same as my dads jackaroo setup....is it?

HRZOOK

will this kit fit a jimny?,
i know that OME 2" coily suspention kits fit a jimny.

mooman wrote:will this kit fit a jimny?,
i know that OME 2" coily suspention kits fit a jimny.

since when has ome had a coily lift? And it wouldnt fit because coily front end is a spring over shock setup whilst jimnys the springs and shocks are seperate.

don't underestimate the interchangability of suzuki parts.
just because one is coil-over doesn't mean that the springs wont fit, i agree that the shock's would be differant, but i'm sure the springs are the same.
the only reason i'm saying this is because i have a magazine artical from NZ where a chap used an OME lift (could have been just the springs) on a Jimny that was for a coily, the mag was also supprised that the kit was an OME.

just curious.