Page 1 of 1
ARHHHH!!! FARKING DIFF!!!!
Posted: Tue Jan 18, 2005 11:46 am
by glen1n
Need to change the diff centre in my 70, but the old one comes off the damn bolts and then doesnt want to budge. It is busted after being welded. Here are some pics.
This is meant to be screwed right in so you cant see the thread, correct? perhaps this be the problem. Tried hitting it around but again it wont budge. I might need to take a grinder to all of it
Look how far its off the DAMN BOLTS!!!!!!!!!!!!
Posted: Tue Jan 18, 2005 12:56 pm
by MY45
Glen see that screw bit get something ad thread it back into the diff as that would mostlikeyl be your problem..
Posted: Tue Jan 18, 2005 3:25 pm
by spazbot
so the center isnt comming out of the housing ?
Posted: Tue Jan 18, 2005 3:35 pm
by Bad JuJu
Dumb ass question ..... are the axles out of the center ????
Posted: Tue Jan 18, 2005 3:58 pm
by bogged
Lump hammer...
Posted: Tue Jan 18, 2005 4:15 pm
by dumbdunce
glen adam is right, the carrier bearing adjuster you can see in that pic is loose, and needs to be screwed back in before the diff will come out. the bad news is, if the carrier bearing retaining bolts are still tight, those screws are really hard to turn.
did you put it together without the carrier bearing adjuster nut stop tabs?? (the little useless looking steel tabs held on the ends of the bearing retainer caps by weedy little M8 bolts)
I would post a pic but there is no room left on the board for nay more pics.
Posted: Tue Jan 18, 2005 5:00 pm
by 4sum4
Its definalty loose you can see the thread and did the centre grinade that will be the cause and I hope that isn`t the one That just had the locker put in or someone will be in trouble
Posted: Wed Jan 19, 2005 7:11 am
by glen1n
Bad JuJu wrote:Dumb ass question ..... are the axles out of the center ????
If the axles were not out the diff wouldnt have come out as far as it did, so keep your dumb ass replies to your self
Posted: Wed Jan 19, 2005 7:24 am
by glen1n
spazbot wrote:so the center isnt comming out of the housing ?
Correct
dumbdAnce wrote: the carrier bearing adjuster you can see in that pic is loose, and needs to be screwed back in before the diff will come out.
Thought this may have been the case, bugger.
4sum4 wrote:I hope that isn`t the one That just had the locker put in or someone will be in trouble
Nah it was the welded rear, so that certain somebody is ok
Thanks for the replies fellas. i'll give it a go later
Posted: Wed Jan 19, 2005 7:58 am
by mkpatrol
glen1n wrote:Bad JuJu wrote:Dumb ass question ..... are the axles out of the center ????
If the axles were not out the diff wouldnt have come out as far as it did, so keep your dumb ass replies to your self
Took the words out of my mouth
Posted: Wed Jan 19, 2005 9:31 am
by MY45
You fixed it yet glen?
Posted: Wed Jan 19, 2005 9:34 am
by MY45
dumbdunce wrote:glen adam is right, the carrier bearing adjuster you can see in that pic is loose, and needs to be screwed back in before the diff will come out. the bad news is, if the carrier bearing retaining bolts are still tight, those screws are really hard to turn.
did you put it together without the carrier bearing adjuster nut stop tabs?? (the little useless looking steel tabs held on the ends of the bearing retainer caps by weedy little M8 bolts)
I would post a pic but there is no room left on the board for nay more pics.
They were on...i think the center just grinaded.
Posted: Wed Jan 19, 2005 9:45 am
by Bad JuJu
STFU A-holes, Hope it never comes out if you answer a reply like that
Posted: Wed Jan 19, 2005 3:19 pm
by glen1n
Bad JuJu wrote:STFU A-holes, Hope it never comes out if you answer a reply like that
Cheers for the input.
Posted: Wed Jan 19, 2005 3:22 pm
by glen1n
MY45 wrote:You fixed it yet glen?
Gonna give it a go later. It was giving me the runs so i need time to cool off.
Posted: Wed Jan 19, 2005 6:55 pm
by glen1n
Bad JuJu wrote:Dumb ass question ..... are the axles out of the center ????
Sorry mate, read it a second time and relised you were saying your question was stupid, not mine. Correct?
Glen
Posted: Wed Jan 19, 2005 8:16 pm
by hypo
glen1n wrote:Bad JuJu wrote:Dumb ass question ..... are the axles out of the center ????
If the axles were not out the diff wouldnt have come out as far as it did, so keep your dumb ass replies to your self
chill out man
he said it may b a dumb question b4 he asked it...
Posted: Wed Jan 19, 2005 8:25 pm
by RUFF
glen1n wrote:Bad JuJu wrote:Dumb ass question ..... are the axles out of the center ????
If the axles were not out the diff wouldnt have come out as far as it did, so keep your dumb ass replies to your self
I was going to ask the exact same Question.
He was only trying to help. Maybe you want to read before you reply next time
Posted: Thu Jan 20, 2005 2:10 pm
by glen1n
hypolux wrote:glen1n wrote:Bad JuJu wrote:Dumb ass question ..... are the axles out of the center ????
If the axles were not out the diff wouldnt have come out as far as it did, so keep your dumb ass replies to your self
chill out man
he said it may b a dumb question b4 he asked it...
i noticed that after i replied, hence my post above yours. Once again i thought he was refering to my question, not his. Sorry dude
Posted: Thu Jan 20, 2005 2:22 pm
by Bad JuJu
Its ok every one ... its sorted now.
Cheers
Posted: Thu Jan 20, 2005 4:40 pm
by dumbdunce
feel the love!
get the diff out yet?
Posted: Thu Jan 20, 2005 4:54 pm
by glen1n
dumbdunce wrote:feel the love!
get the diff out yet?
nah got maggot yesterday, it was to hot today, and it's about to thunder now. Maybe tomorrow.
Posted: Fri Jan 21, 2005 8:44 am
by +dj_hansen+
This should be of some use dude....
Posted: Fri Jan 21, 2005 2:18 pm
by glen1n
+dj_hansen+ wrote:This should be of some use dude....
Where would we be without it?