OK, here's the deal. I've been trying to figure out how to get a 5 link under the front of my Sierra but since the room is pretty tight up there I can't see any way to do it unless i bend the links. The bend would be sort of a dog-leg with the 2 ends of the link remaining parallel to each other but offset in the horizontal plane. This is because i want the links to attach on the inside of the chassis rails and attach to the diff in line with the chassis rails.
My question is, is this doable or just an extraodinarily bad idea? On top of that, is it possible that it would be passed by an engineer?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Bending links
Moderators: toaddog, TWISTY, V8Patrol, Moderators
from my own experience I have found that running bent links works OK, the only niggly little problem is that depending on the situation it can load up the bushes on some weird angles that they don't like and they end up tearing up. I had this problem with triangulated links the were bent in the vertical plane, moved some things around so I could run straight links and the problem seemed to correct itself..
be carefull of you links hitting the bottom of the chassis rail on the compressed side when the other side is drooped away. The rotating arc of the link will be much, much bigger than the link itself because of the dog-leg in it...
be carefull of you links hitting the bottom of the chassis rail on the compressed side when the other side is drooped away. The rotating arc of the link will be much, much bigger than the link itself because of the dog-leg in it...
I intended running a johnny joint or the like on one end of the links, so that should help with the binding, no?
As for the links hitting the chassis rail on the compression side, i'll just have to make sure i build it with enough clearance. Good point though.
My main concerns are even if i build the links with heavier material is that going to stop them bending? will i have to run another brace on the links somehow? I reckon if they are made from heavy wall DOM they should be ok, but what do i know???
As for the links hitting the chassis rail on the compression side, i'll just have to make sure i build it with enough clearance. Good point though.
My main concerns are even if i build the links with heavier material is that going to stop them bending? will i have to run another brace on the links somehow? I reckon if they are made from heavy wall DOM they should be ok, but what do i know???
Damo wrote:I intended running a johnny joint or the like on one end of the links, so that should help with the binding, no?
it isn't really binding that is the problem.. picture a link mounted double shear to a crossmember: there is no leverage on the pin at all, the tension/compression on each side cancel each other out. now if you imagine that link with a z-type bend in it, then tention and compression is being concentrated on an imaginary point somewhere to the side of the mount, so it ends up trying to twist the bush on a different axis to its own and push it somewhat sideways... works in my head anyway
Damo wrote:My main concerns are even if i build the links with heavier material is that going to stop them bending? will i have to run another brace on the links somehow? I reckon if they are made from heavy wall DOM they should be ok, but what do i know???
If you use good heavy wall junk, upper arms should be OK, if you are bending the lowers , gusset them, cause they will hit things and all the force of the impact will zero in on your bend....
Wendle wrote:it isn't really binding that is the problem.. picture a link mounted double shear to a crossmember: there is no leverage on the pin at all, the tension/compression on each side cancel each other out. now if you imagine that link with a z-type bend in it, then tention and compression is being concentrated on an imaginary point somewhere to the side of the mount, so it ends up trying to twist the bush on a different axis to its own and push it somewhat sideways... works in my head anyway
I think I can see what you mean, because the ends will be rotating around 2 different axes. Just running through it in my head I can't see it being a big problem, as any movement that cant be taken up by the joint at one end can be taken up by the joint at the other end of the link. Works in my head anyway
Who is online
Users browsing this forum: No registered users and 0 guests