Link Ends

[antt]

just wondering if its possible to buy complete link ends (standard nissan ones), with the rubber insert and tube that ya can weld into a length of tube to make custom lengths?? and if so, where could we find some

and/or, what size is the tube that is required to push a standard nissan rubber bushing into?

and what sorta $$$'s would ya expect to pay for the genuine rubber bushes???

[N*A*M]

i think it's 50mm antt. i'm looking to make a new engine mount with the same bushing. hook us up if you find cheap ones

carlton said to use 50NB pipe and cut the seam, compress it tighter and reweld. it should be close enough.

[Wendle]

carlton said to use 50NB pipe and cut the seam, compress it tighter and reweld. it should be close enough.

there is a seamless one with a 5.4mm wall which the bushes press into perfect but it can be hard to get a hold of. the engine and trans mounts in my new buggy have the tube nam is talking about - cut and squished.

[wannaberacer]

I was going to do the same thing using Range Rover bushes to make my own arms....but after pricing the bits and pieces it was gonna be cheaper (and probably better) to get these ones:

http://www.offroadindustries.com/suspen ... lyflex.htm

They sell you the sleeve also...just weld your bar on and away you go. Would give heaps better flex than standard nissan ones

[antt]

what are they worth?

[wannaberacer]

I think from memory it was gonna be close to $50 for the bush and casing....and at the time i was going to buy bulk so the price was going to be less.

I was quoted more than $40 for the RR bush alone, so it sounded like a good buy to me to use the ORI bushes.

Whats a standard Nissan GQ trailing arm bush worth?

[Bartso]

hey ant im doing this as well making my own arms i heard those ones from off road industries don't offer as much flex as the standard nissan bushes i think i read it in 4wd monthly

i saw some where you can buy the ends of your arms already done im looking for them now

[berazafi]

PM bundyrum4x4 (aka Greg), he may be able to help you out

[A1]

just wondering if its possible to buy complete link ends (standard nissan ones), with the rubber insert and tube that ya can weld into a length of tube to make custom lengths?? and if so, where could we find some

and/or, what size is the tube that is required to push a standard nissan rubber bushing into?

and what sorta $$$'s would ya expect to pay for the genuine rubber bushes???

antt ring Overkill as he machines these up (the bush tube ) ..... and are very reasonably priced and they fit perfectly i have them on my 4 link rear ............ the nissan bushes are bout $35 buck ea from nissan ..(well thats wat i paid a while back )Sam may very well beable to supply these aswell ring and find out ........


He also uses 12mm wall thick seamless for his links .....BEEF may beable to set you up with complete links to your sizes ?


Dan

[DaveS3]

I think from memory it was gonna be close to $50 for the bush and casing....and at the time i was going to buy bulk so the price was going to be less.

I was quoted more than $40 for the RR bush alone, so it sounded like a good buy to me to use the ORI bushes.

Whats a standard Nissan GQ trailing arm bush worth?

$40 for a RR bush is pretty steep.

Can buy pretty good rubber ones (mushroom, not OE but good) at about $10 - $15 each - These will flex much better

Have these at the chassis end and Nissans or whatever at the other.

Dave

[antt]

its all good, i've sourced some original nissan ones off a member on here, cheers muzza_fatire

[N*A*M]

sean hooked me up too