36's under a GQ??
Posted: Thu May 19, 2005 6:46 am
Im going to be getting a GQ in the next month and was wondering what was the min lift/guard cutting that has to be done to be able to run some 36" pedes under it?
Page 1 of 1
Posted: Thu May 19, 2005 7:03 am
i got 5 inch coils and 2 inch body lift and run 35's off road . i would say that it may just be enough to get 36 pedes. the only issue u may have is the back of ur front guards unless u use the big balls radius arm spacer and ditch the factory flares and mud flaps..i dare say u will need to do that at the back as well. get ur lift up, run the tyres and chop enough from ur gaurds so they clear. but as i said with my lift u will be pretty close to the money..
Posted: Thu May 19, 2005 7:19 am
had 5 inch coils and 40mm body as well to run 36's...
had a wizard 5 link in the front so was able to centre the wheel in the front... no probs at all.
tiny bit of trimmin on the front and rear guards at the back part near mudflaps to allow the full flex to go thru without rubbing..
TOM
had a wizard 5 link in the front so was able to centre the wheel in the front... no probs at all.
tiny bit of trimmin on the front and rear guards at the back part near mudflaps to allow the full flex to go thru without rubbing..
TOM
Posted: Thu May 19, 2005 8:02 am
I run 36" TSL's, with a 2" bodylift, and 2" coils, with 1" coil spacers. I have removed the factory mudflaps and flares. I also trimmed a section about 2" deep on the bottom corner of the front guard, only about 6" up. I leave the swaybars on, and have no rubbing problems. I guess if the swaybars were removed, I would have problems then.
Posted: Thu May 19, 2005 8:03 am
I run 36" TSL's, with a 2" bodylift, and 2" coils, with 1" coil spacers. I have removed the factory mudflaps and flares. I also trimmed a section about 2" deep on the bottom corner of the front guard, only about 6" up. I leave the swaybars on, and have no rubbing problems. I guess if the swaybars were removed, I would have problems then.
Posted: Thu May 19, 2005 9:02 am
I have 6" coils and 36s with no gaurd chop is a tight fit
Posted: Thu May 19, 2005 10:01 am
i run 35s with a 2in body lift
Posted: Thu May 19, 2005 10:20 am
We run Q78s with 3" springs and a guard chop.
Posted: Thu May 19, 2005 11:58 am
run 37's with 3" springs, used to be 4" but sagged now, and 2" body
trimmed gaurds too.
trimmed gaurds too.
Posted: Thu May 19, 2005 6:00 pm
they will fit with just a guard trim. how much lift/body lift is up to you. edit: sorry, unless its a wagon then see above
bru
bru
Posted: Thu May 19, 2005 8:58 pm
thanks for the help guys.
sorry i didnt put in much info, its going to be a wagon and am pretty sure ill go with a 4" spring lift and 2" body and then get out the angle grinder from there and just take as much off the guards as i have to.
sorry i didnt put in much info, its going to be a wagon and am pretty sure ill go with a 4" spring lift and 2" body and then get out the angle grinder from there and just take as much off the guards as i have to.
Posted: Thu May 19, 2005 9:53 pm
thats wot we like to hear angle grinder on the guards