Wanting to lift the 130 2"ish to get clearance for bigger tyres....
Decided on the Ironman kit, very good value for money and haven't heard of any problems with them...
Only issue may be that they don't seem do heavy enough rear springs in length I need.....
I currently have stock rears at (as best I can measure with wheel unweighted) 420mm long x 170ish mm external diametre x 20-21mm thick. (not measured inner 'helpers', as not going to replace them)
Fronts are 370x150ishx17mm
The fronts come off fine, with options available of 400/408mm, 415/425 and 420/430 ironman springs in correct width and thickness... sweet. ( I hear of RR alternative, back to that later..)
Rears options are 440 or 480mm tall, but both only in 17mm diametre....methinks way too soft compared to current 20-21mm thick with added inner 'helper' springs.
'Hiline' on the AULRO site said he used RR springs all round to get 3" lift, but my inquiries so far say perfect option for front, but shorter than stock rears, and much smaller diametre.
I just need to know who has lifted their 130 utes a similar amount (or done a lift for someone), what size springs did you use, what weight of spring will I need in rear without inner spring (I want it softer than it is currently, but not so as I can't tow and carry loads, do other vehicle makes run a compatible spring size (rumours or Nissan?)
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
defender lift question
Moderator: Micka
Re: defender lift question
Speak to Micka has has lifted his defender & is very happy with the jobmoorey wrote:Wanting to lift the 130 2"ish to get clearance for bigger tyres....
Decided on the Ironman kit, very good value for money and haven't heard of any problems with them...
Only issue may be that they don't seem do heavy enough rear springs in length I need.....
I currently have stock rears at (as best I can measure with wheel unweighted) 420mm long x 170ish mm external diametre x 20-21mm thick. (not measured inner 'helpers', as not going to replace them)
Fronts are 370x150ishx17mm
The fronts come off fine, with options available of 400/408mm, 415/425 and 420/430 ironman springs in correct width and thickness... sweet. ( I hear of RR alternative, back to that later..)
Rears options are 440 or 480mm tall, but both only in 17mm diametre....methinks way too soft compared to current 20-21mm thick with added inner 'helper' springs.
'Hiline' on the AULRO site said he used RR springs all round to get 3" lift, but my inquiries so far say perfect option for front, but shorter than stock rears, and much smaller diametre.
I just need to know who has lifted their 130 utes a similar amount (or done a lift for someone), what size springs did you use, what weight of spring will I need in rear without inner spring (I want it softer than it is currently, but not so as I can't tow and carry loads, do other vehicle makes run a compatible spring size (rumours or Nissan?)
cheers johnz
LOVELLS-EFS-DOBINSON-PROCOMP-BILSTEIN-KONI-RANCHO-TOUGHDOG-BLUEMAX
COIL SPACERS from $46pr
4WD SUSPENSION & BODYLIFTS 0418780611 A/H PH/FAX 07 33512692 - www.zordos4wdsuspension.com.au
COIL SPACERS from $46pr
4WD SUSPENSION & BODYLIFTS 0418780611 A/H PH/FAX 07 33512692 - www.zordos4wdsuspension.com.au
Who is online
Users browsing this forum: No registered users and 0 guests