How hard is it to install an adj panhard rod on a 4 inch lifted 80 series cruiser and how do I do it?
Thanks
Burnsy
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Panhard Rod install
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Road Ranger
Its not hard at all to setup, putting it on can be a slight headache but if there are two of you its easy.
Firkst of all, get under the vehicle and adjust the rod so its as close to the correct length as possible. Install it onto the 4b. If it wont line up this where you get your mate to GENTLY shake the cruiser from side to side until it flops in.
Now, get out the trusty tape measure, measure the length of each trailing arm (or measure L and R lower trailing arm for the rear). Make sure they are the excactly the same length. If they are, proceed to step 3.
Measure diagonally from trailing arm left to trailing arm right, for instance, the forward bolt of the left arm to the rear bolt of the right arm, and then rear bolt of the left arm to the front bolt of the right arm. Just remember to measure these whilst the car is parked on a dead flat surface!
If you adjusted the panhard right, then these distances will be identical. If you didn't (which 9 out 10 time it will be wrong) then you need to figure out which way in or out you need to adjust the panhard bar which is usually abouit 3/4 of the total difference between the two. Draw yourself a little picture of the arms and dimentions and you will work this out. Every time its readjusted make sure you bounce the car around a bit to re-settle the suspension.
Can be time consuming but this is exactly how Pedders or Midas or any mechanic worth his shit will do it.
Firkst of all, get under the vehicle and adjust the rod so its as close to the correct length as possible. Install it onto the 4b. If it wont line up this where you get your mate to GENTLY shake the cruiser from side to side until it flops in.
Now, get out the trusty tape measure, measure the length of each trailing arm (or measure L and R lower trailing arm for the rear). Make sure they are the excactly the same length. If they are, proceed to step 3.
Measure diagonally from trailing arm left to trailing arm right, for instance, the forward bolt of the left arm to the rear bolt of the right arm, and then rear bolt of the left arm to the front bolt of the right arm. Just remember to measure these whilst the car is parked on a dead flat surface!
If you adjusted the panhard right, then these distances will be identical. If you didn't (which 9 out 10 time it will be wrong) then you need to figure out which way in or out you need to adjust the panhard bar which is usually abouit 3/4 of the total difference between the two. Draw yourself a little picture of the arms and dimentions and you will work this out. Every time its readjusted make sure you bounce the car around a bit to re-settle the suspension.
Can be time consuming but this is exactly how Pedders or Midas or any mechanic worth his shit will do it.
\m/
...
THANKYOU... OMG THANKYOU...
I have been waiting for a DECENT explanation of how you properly set up adjustable panhard rods. I got mine and and eyed it up
then got the old boy to shake the car as you said. But looking I can tell the track is out...
I have been waiting for a DECENT explanation of how you properly set up adjustable panhard rods. I got mine and and eyed it up
then got the old boy to shake the car as you said. But looking I can tell the track is out...[quote="MSCHIF"]SPUA its like shaving a barbie dolls head, amusing but pointless.[/quote]
Who is online
Users browsing this forum: No registered users and 3 guests