Anyone replaced their Lucas Elctronic Dizzy with aftermarke

Post by **Rovernaut** » Wed Dec 28, 2005 10:06 am

Has anyone replaced the Lucas electronic Dizzy with the ignition amp with any thing else.
If so what worked?

Post by **TRobbo** » Wed Dec 28, 2005 3:31 pm

On my first 3.5 I changed to dizzy from points to electronic with a piranha kit. Easy to do and better overall but still had some water problems and eventually advance problems as the dizzy progressively wore. Then converted the 3.5 with a bosch dizzy purchased from Ritters - worked a treat.
More recently had a 3.9 taken to 4.6 with the dizzy replaced and set up by scorcher (?) in Mitcham. (Off Maroondah hwy turn left down Rooks Road then the 1st left) can't remember exactly what they did but didn't have any problems.

Post by **J Top** » Wed Dec 28, 2005 5:00 pm

I have seen GM HEI's fitted but don't know the ins and outs
J Top

Post by **Rovernaut** » Wed Dec 28, 2005 8:42 pm

TRobbo wrote:On my first 3.5 I changed to dizzy from points to electronic with a piranha kit. Easy to do and better overall but still had some water problems and eventually advance problems as the dizzy progressively wore. Then converted the 3.5 with a bosch dizzy purchased from Ritters - worked a treat.
More recently had a 3.9 taken to 4.6 with the dizzy replaced and set up by scorcher (?) in Mitcham. (Off Maroondah hwy turn left down Rooks Road then the 1st left) can't remember exactly what they did but didn't have any problems.

Yep bought stuff from them before. Performance ignitions.
Apparntly gurus on dizzys.
I fnot a rude qu. What was the cost of the scorcher?

Post by **Loanrangie** » Tue Jan 03, 2006 8:43 am

I have had a pefromance ignition ( scorcher ) bosch dizzy on 81 rangie for 11 years, as soon as i fitted it there was a performance gain - engine would rev harder and economy was improved. That and a 350 holley was the best mods i have done to it, i also have a gm hei dizzy that will go on the 3.5 when i swap that out of my 85 rr and into the 81 ( now a ute) - being replaced with a 4.4. A buick 350 hei will fit and also a buick v6 if you change the shaft. This is a buick v6 body with olds shaft on a 4.4.

Post by **Owen** » Tue Jan 03, 2006 3:05 pm

Go with the scorcher, I could not be happier with mine. It was about $550.

Post by **old tom** » Tue Jan 03, 2006 7:42 pm

VT holden dizzy best thing i did

Post by **Soundsgood** » Tue Jan 03, 2006 9:30 pm

I have recenly installed Ford EDIS and coil packs. Have left the dist in place to drive the oil pump. The EDIS gets its advance and dwell signal from an after market ECU. All working well - so far.
Bruce

Post by **BIg StEvE** » Sat Feb 18, 2006 8:01 am

Sorry been digging again. Is this the performace ignition shop u guys were recomending?

http://www.yellowpages.com.au/onlineSol ... 16e2&st=bn

cheers

steve

Post by **BIg StEvE** » Sat Feb 18, 2006 8:06 am

Answered my own question!

http://www.performanceignition.com.au/i ... 20394-0365

Post by **F'n_Rover** » Sat May 20, 2006 9:07 pm

sorry for another dig :

Soundsgood wrote:I have recenly installed Ford EDIS and coil packs. Have left the dist in place to drive the oil pump. The EDIS gets its advance and dwell signal from an after market ECU. All working well - so far.
Bruce

Paging bruce :
What ford ignition module did you use ? I thought they where all built into the ecu in the oz fords ?

I'm going down the edis road atm, Ive got a 35 tooth crank angle cog and sensor, but am trying to find a matching ford ignition module (6cyl).
I was going to ditch the ford setup and go the holden V6..... but if i can source ford...

I'll be driving it from the megasquirt ecu.

Thanks

Post by **Euan** » Mon May 22, 2006 12:28 am

Ive got 4.4 with a buick hei run by megasquirt 2. No more changing fly weight springs or vacum advance modules.

Outer Limits 4x4 Board

Anyone replaced their Lucas Elctronic Dizzy with aftermarke

Anyone replaced their Lucas Elctronic Dizzy with aftermarke

Dissy

Who is online