Outer Limits 4x4 Board

Rotating the plate allows the installation of a inverted v, the shock remains up right.
rotating and swapping the shock plate the shock can swing east west allowing the top of the shock to be mounted hi to the middle of the frame bi the way of a cross member

It’s a buyers market. Now day

Good luck with the sale

I’m planning to rotate the u-bolt plate so that i can install a inverted shock setup (see pic)


If you can see any faults with the plan i.e. weaknesses/disadvantage let me know


Thanks rob
[/img]

cool

Yes that’s a lot of water on the vent i’ll save that idea for sports cars

It’s a good plan to run it in to the wheel arch .but if you get stuck in the deep end the water will fill the space ,don’t you think

I don’t know much about the classers of commodore there from a sedan type, of a vr senator.
I’m thinking the only way to fit them will be, a inverted /v type set up looks farley easy to .do have you got any suggestions on inverted set up. I’m looking at cabinets for the back and so integrate a lo ...

Rear Shocks (f300)------c

Hello people

I read that commodore vs shocks may fit the rear of the f300.spoted sum on ebay and obtained a set for $5 bucks, and they fit. But top out on compression.i have extended shackles 70mm
They are VR VS COMMODORE MONROE GT GAS SPORTS SHOCKS
Rounder bout to with ...

I was thinking where is you brake booster.
O
Left hand drive

Hay y not go in to the fire wall and draw air from the air/con ducked at the windscreen

Thanks for the replies

Planning a to rack up so k’s in the next month

So it’s good to hear the boxes under vibes hold up

Its lasted like this for 5 years can i expect a pop followed bye sum hi-revving.

Mostly noticeable in 3rd. no vibes in 1st if i change gear early 3 or 4 starts off good and then vibes fade in and out (Mostly noticeable in 3rd) don’t think its road speed related. Say I’m going down a hill vibes are there but fades in and out faster properly because there’s less strain on the box ...

Hello all
I’ve had the Feroza for about 5 years and still have a vibration in 3rd

Can any one help on this one .say I put it in 3rd early so that the car is under load (say 1900 rev) all sounds good .as I clime in the rev range still good and no vibes I get to about 2100 vibration starts fading ...

Referring to the power its o k, it is a feroza after all. in my case Referring to the power again it all or unthinking .and it seams to be all or unthinking when it comes to power mods .ill wait till i can put the feroza on a swb rock frame, v 6 and hilux axels. even then all that work and then your ...

MM are you referring to the HD or the feroza when you say so why even bother ? or until you get locker gearing .?

Hello and flashback

F300 HD turbo t25 stock in’er ripped it out thow. My setup was unreliable still got the manifold throw if yore interested hi mount style set to a t25 flange, 1 and 3 joined 2 and 4 joined outer .

Didn’t think it was that good until I polled it off .but I’m happier with out it e ...

i noticed the same thing in the body behind the rear wheels not mud but damp powdery stuff .a lesser 4by and i wood have found holes,wise non as bunderasyndrome

That rock’s no pun intended. Nice!!!!!!! Nice!!!!!!! Nice!!!!!!!

Ill try the grease up. thanks to all

Hello all
A bit late, butt new 4 me.
Sum movement is normal and part of the design of the shaft, cool.
I seem to get about 8-10 mm of movement making a lot of noise

yes st165 w2a intercooler looking for one for sum time now
hay maybe u can give me yours ! hay its a bad joke

that sounds like good out put(260hp)
got sum tips 4 runing a turbo on the HD-E

its a standard f300 feroza engine with a parasite Garrett t25
still running it in, so cant say much on performances.
turbo's from a Nissan SR20DET i think maybe a bit to big this1.6 looking at a t2o with t25 flange.
already got a sh^$ load of custom fab and I've gotten so much welding burn people ...

got a new camera ,snap snap
this rx7 seats look nice,sum turbo pix too .
just need a middle pipe.2 1/4" fun
http://i271.photobucket.com/albums/jj158/berry-lo_2008/feroza1.jpg [/img]
[/img] http://i271.photobucket.com/albums/jj158/berry-lo_2008/feroza1-10.jpg
rx7 seats on feroza rails
http ...

can you guys recommend fabricators!!!

just got a quot on lower con-arms -ex..
do you think this quot is good
---------------------------------------------------------------------------
fabricator has quoted:

for P20 ALLOY STEEL price = $340 each + GST based on 2 off

Above includes delivery within Sydney metro.

We trust the above ...

[/img]
thanks rob

snap
i think this mouse might help

Extensions of lower control arms
ill cheek that out
i think that is a flat bar with a slight bend,sum drill points and receiving shapes .

f300 custom control arms
hay all
looking for info on widening the a-arms on a f300 narrow-track
I'm thinking
- cleaning of slug welds and opening the box section.then stagger the cuts ,box then flat.grafting and adding the length .at the same time adding reinforcement walls inside the box and ...

Got the same thing cleaning the afro with a gurney
Apparently water get’s into the spark plug tubs