Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Jackshaft uni change

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Jackshaft uni change

Post by v840 »

Ok, Got a bad clunking sound coming from my driveline. Jacked the rear up, disconnected the front shaft and put it in first and it was still there. That rules out front axle/driveshaft.

Next, I disconnected the rear shaft and it was still there ruling out the rear axle/shaft.

This leaves gbox and tcase. Removed tcase from vehicle and pulled out the jackshaft. started the car up and put it in first and the clunk was gone.

So it is either the jackshaft or the tcase right? Now, I figure changing uni's would be a damn sight easier than pulling apart a tcase so out come the handy circlip pliers and check it out. wtf? no circlips!

I also spun the flanges on the tcase by hand and I couldnt hear any sounds not that I can spin it that fast by hand :D
Which leads me to believe it is the jackshaft..........unless someone on here can tell me otherwise ;)

So my question is: How the fark do you remove and replace the uni's in an 89 sierra jackshaft? If it would help I can put up pics.
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

Some uni's might have internal circlips , but could be missing , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

All I can see internally is one rubber and one copper(?) washer. Ive rotated them around the uni cup and cant see any break in the circumference. Short of a cutting disc I cant see how to get them off. Is there a trick to determining if it has internal/external circlips?
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

Does the jackshaft have the position where the clips might have been , are both ends the same , no clips or just one end are missing , is there sideways movement in th uni , Cheers Paul
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

No position where they might have been.
Both ends are the same.
No clips are visible on the any of the yokes/unis.
There is a small amount of movement but not alot. I figured since it was out it wouldnt hurt to change them regardless.

After going back over your questions, I feel like a dumbarse :D
I guess the question should have been: How do you change internal circlipped uni joints? :)
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

So are they internal clips , cause i think you said one was gold , if they are just remove and change , also do you know how to change them , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

MART wrote:So are they internal clips , cause i think you said one was gold , if they are just remove and change , also do you know how to change them , Cheers Paul.
Sorry dude, I dont really understand what you are saying.

Yes, I think they must be internal clips, but Im by no means sure.

It does look like its made of copper but again, Im not positive.

I cant see how to remove them as they dont have a break in the circumference of the washer?

No, I dont know how to change them, hence my question.
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

Can you post some pics , cause I,m pretty sure there is only two types , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

Just looking at mine and there external , do you have a manual as info on how to change is in there , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

No manual unfortunately. Looking at the unis on my driveshafts, they are all external but Im fairly sure that the jackshaft ones are internals.
My camera is with my girlfriend till tomorrow but I will put some pics up then.


So, how are unis with internal circlips removed???
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

unis

Post by want33s »

Mine is 89 and all unis have internal circlips. The gap in the clip is only about 10mm so check all the way around. The gap may have rotated to the inside.
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

Just checked mine and mine is 85 and they are external , as want 33s said there should be a gap in the clip and they are thicker than external clips , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Re: unis

Post by v840 »

want33s wrote:Mine is 89 and all unis have internal circlips. The gap in the clip is only about 10mm so check all the way around. The gap may have rotated to the inside.
10mm is quite a gap! :)

Assuming you mean 1mm Ive checked them all over pretty comprehensively. Having said that however, They were pretty covered in gunk and I was checking them under fairly low light.

They're soaking in degreaser at them moment so I'll check them again tomorrow.
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Re: unis

Post by want33s »

v840 wrote:
want33s wrote:Mine is 89 and all unis have internal circlips. The gap in the clip is only about 10mm so check all the way around. The gap may have rotated to the inside.
10mm is quite a gap! :)

Assuming you mean 1mm Ive checked them all over pretty comprehensively. Having said that however, They were pretty covered in gunk and I was checking them under fairly low light.

They're soaking in degreaser at them moment so I'll check them again tomorrow.
NO, I mean 10mm.
Here is a pic. Its not a Suzuki Uni but its close enough. See how the clips aren't a full circle? There is a gap (in this pic about 20mm as this is a Holden 6 cyl uni)) ......
Image
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

nup, mine is definitely different to that. thanks for the help though. :D

Ill keep staring at it in the hope the answer will come to me :P
Otherwise its the grinder :armsup:
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

jackshaft

Post by want33s »

Post a pic and we might be able to help!
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

Ok here's a couple of pics:

Ive removed the two washers using a screwdriver :) on the horizontal axis of the uni. You can see the washers on the vertical axis. they go right round so they aint no circlip :?
Image


This is the view from the top. No circlip here either :x
Image

At this stage I think Im just going to go to a wrecker and get a another jackshaft with the externally clipped unis and save the headaches. Unless someone here can let me know where Im going wrong?
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 870
Joined: Sat Jun 03, 2006 5:32 pm
Location: sydney

Post by MART »

If that is a standard jackshaft , somebody has played with it , shouldn,t cost much for a new one , you won't get that apart and if you did it wouldn't use it , Cheers Paul
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Top
Posts: 6221
Joined: Tue May 31, 2005 12:51 pm
Location: Sydney

Post by v840 »

MART wrote:If that is a standard jackshaft , somebody has played with it , shouldn,t cost much for a new one , you won't get that apart and if you did it wouldn't use it , Cheers Paul
Thats what I wanted to hear. Thanks mate!
|^^^^^^^^^^^^^^| ||
|.........SUZUKI..........| ||'|";, ____.
|_..._..._______===|=||_|__|..., ]
(@)'(@)"""''"**|(@)(@)*****''(@)
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

jackshaft uni

Post by want33s »

That is a factory pressed unit that has to be machined to remove. Toyota have used this type of uni for years on non Australian built cars. Uni can be replaced at cost but I'd replace the whole shaft with a replaceable uni type.
Top
Posts: 22
Joined: Fri Mar 17, 2006 2:27 pm
Location: Melbourne

Post by intens »

That looks like my jimny one :x dont think the uni's are replacable :twisted:
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 80 guests