Truck ones are basically the same but with a deeper pan (extra litre or so)cloughy wrote:Camaro sumpBourbon wrote:
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Gen 3 in GQ
Moderators: toaddog, TWISTY, V8Patrol, Moderators
dellow will tell you they dont do one, but I have seen three dellows small block chev bell housings that have been modified to suit the gen3. These were all in comp cars during this years OBC, However this requires the gear box and transfer to be moved forward and both drive shafts to be modified. CRS will tell you the same as dellow, but with mods it will fit the same as dellows.
As for Marks I have heard a few stories however this has not stoped me from buying one for my GQ. Marks kit is a lot easier to fit and there is no drive line mods to do, plus you can use any gen 3 clutch. Engine mounts are easy to make and the majority of the comp cars I have seen were running GQ trailing arm bushes, set up as mounts. I believe that Dale from 2Dxtreme has made some for a customer and wizard performance,
and cas jones in wa, so take your pick.
The new 6L exhaust manifolds will apparently fit without mods. 5.7L can be modified using a 2 bolt flange to replace the original cast flange and extractors are available custom made, but probably wont give you that much more bang for your buck.
Sitting the engine back close to the fire wall is not going to give you any advantage as the gen3 is a lot lighter than the nissan 6 and its weight mass is going to be further back anyway.
Hope this helps.
Gouldy
As for Marks I have heard a few stories however this has not stoped me from buying one for my GQ. Marks kit is a lot easier to fit and there is no drive line mods to do, plus you can use any gen 3 clutch. Engine mounts are easy to make and the majority of the comp cars I have seen were running GQ trailing arm bushes, set up as mounts. I believe that Dale from 2Dxtreme has made some for a customer and wizard performance,
and cas jones in wa, so take your pick.
The new 6L exhaust manifolds will apparently fit without mods. 5.7L can be modified using a 2 bolt flange to replace the original cast flange and extractors are available custom made, but probably wont give you that much more bang for your buck.
Sitting the engine back close to the fire wall is not going to give you any advantage as the gen3 is a lot lighter than the nissan 6 and its weight mass is going to be further back anyway.
Hope this helps.
Gouldy
GQ. Supercharged LSX 427, 500rwkw. camtech cam,90mm Holley Throttle Body. twin 4"exhaust, big fuel system, King bypass shocks and bumpstops.
What issues have there been with the marks input shafts.henry wrote:Have there been issues with the marks input shaft adaptor in the marks kit?
I want the engine to sit as far back as possible. Do dellows supply a complete bell housing?
Do CRS do a bell housing?
I have seen them need to be shortened slightly, but only with harrop cranks, is it the same thing in a gen 3??
6L truck sump part numbers #12560392 or #12577396 from Eagle Auto Spares in Melbourne ph 03 8710 3000 cost $4006.5 rangie wrote:Truck ones are basically the same but with a deeper pan (extra litre or so)cloughy wrote:Camaro sumpBourbon wrote:
cheers
gouldy
GQ. Supercharged LSX 427, 500rwkw. camtech cam,90mm Holley Throttle Body. twin 4"exhaust, big fuel system, King bypass shocks and bumpstops.
Who is online
Users browsing this forum: No registered users and 14 guests