gq petrol turbo, carby gas

Post by **rangiedan** » Wed Aug 29, 2007 8:58 pm

hey guys,

i have recently brought a GQ patrol petrol gas and i was wanting to put a turbo on to it..

was wondering what was the best way to go about doing this.. should i just run gas? or can you incorporate petrol with out going the EFi...

what size turbo.. Basically just wanna know any info you might have that could help me..

thanks heaps

rangiedan..

Post by **bigbennymq** » Wed Aug 29, 2007 9:08 pm

Just go straight to Andrew on ONTRACK 4x4 he is the god of 4.2's lol

Post by **tna racing** » Wed Aug 29, 2007 9:10 pm

is it rb30 or 4.2?

Post by **bagsy** » Wed Aug 29, 2007 9:26 pm

check this out

http://www.biders4wd.com

Post by **tna racing** » Fri Aug 31, 2007 9:45 am

we are runnin a rb30 with turbo, its on gas research, goes hard as, i would look into it

Post by **tna racing** » Fri Aug 31, 2007 10:50 am

also we are running a to4e turbo with highmount manifold n it goes good

Post by **brentz** » Fri Aug 31, 2007 7:55 pm

ive heard something about that the gas powers the turno bettter or something on these motors for some reason?
my mates brother had a swb gq turbo petrol n went for a ride in it and it was great but a bit icky and then he did it on two straight gas tanks and it was a beast ran great and was crazy fast!!! lol

cheerz brentz

Post by **ats4x4dotcom** » Fri Aug 31, 2007 9:49 pm

making a manifold isnt difficult, and the carb will take around 8 psi without any mods, and a 225 or 425 mixer for the lpg if lpg injection isnt in the budget.

8 psi with intercooler, carb, should make around 150rwkw without stress.

Post by **PGS 4WD** » Fri Aug 31, 2007 9:57 pm

I've done a heap of TB42's with Gasresearch amongst 100's of other vehicles in my 10 years tuning at Gasresearch Performance Centre.

Its certainly simpler (and cheaper) to select a fuel but it is possible to blow through impco and a petrol carby, the better duel fuel performance is with EFI and a Gasreserch Carby though. My previous four wheel drive was straight LPG TB42 with a Delco 808(VN-VP) computer running the ignition for a full 3D igniton MAP which is a must for optimum performance in a boosted engine.

Prior to that I had a twin Gasresearch carby VK commodore running a Delco 808 that was duel fuel EFI 12.7 sec @ 106 mph 220 rwKw 5.0L solid cam head work balance and compression.

Before I moved to PGS I was tuning Andrews(On Track) Gasresearch vehicles but its a long way from Cambelfield to Mornington.
You may find as I did the straight LPG limiting in the long distance events so I have gone to petrol only for my new Gen 3 turbo truck as I want to do more long distance event and LPG is a pain for availability, also I get a bigger thrill from tuning the EFI petrol vehicles these days.

I'm happy to offer any advice from my experience if you are interested.

Joel

Post by **dansedgli** » Sat Sep 01, 2007 1:44 pm

Would you need to enclose the carby to run boost or can you just seal up the top of it and run the piping from the intercooler/impco mixer to it?

What happens to the carby once you start exceeding 8psi?

Im guessing you would tune the ignition so that the car runs good with LPG allowing you to limp home on petrol if you ran out of LPG or it stopped working?

That is the only reason I want to keep dual fuel.

Would a high flow VL turbo be a good match for the low revving 4.2 aiming for no more than 150rwkw?

Post by **tna racing** » Sat Sep 01, 2007 1:51 pm

[quote="dansedgli"]Would you need to enclose the carby to run boost or can you just seal up the top of it and run the piping from the intercooler/impco mixer to it?

What happens to the carby once you start exceeding 8psi?

Im guessing you would tune the ignition so that the car runs good with LPG allowing you to limp home on petrol if you ran out of LPG or it stopped working?

That is the only I want to keep dual fuel.

Would a high flow VL turbo be a good match for the low revving 4.2 aiming for no more than 150rwkw?[/quote

hey mate impaco mixers arnt any good

Post by **dansedgli** » Sat Sep 01, 2007 2:17 pm

Why is that?

Post by **tna racing** » Sat Sep 01, 2007 2:19 pm

not enough gas flow thats y we changed ours

Post by **dansedgli** » Sat Sep 01, 2007 2:35 pm

Bugger.

What kind of power were you making?

Post by **tna racing** » Sat Sep 01, 2007 11:12 pm

were making170rwkw b2 gas research convertor is perfect

Post by **PGS 4WD** » Sun Sep 02, 2007 8:09 am

Many stock carbies will handle about 5-8 psi without being sealed in a box, however above that the seals and butterfly shaft become prone to leaking. The butterfly shafts need to be in good condition and sometimes have a positive seal fitted to stop boost and fuel spraying out under the bonnet. Also when on LPG any lack of sealing will let LPG and boost come into the engine bay when on boost(not desireable)
I've found that if using 98 fuel the ignition requirenents are similar to LPG so a suitable compromise is acheivable , however a distributor regraph and possibly a retard unit will be required.
Most people rather the LPG for regular use and the petrol as the back up as the PLG dosent suffer from issues on hills due to fuel sloshing around the fuel bowl.

Joel

Post by **rangiedan** » Mon Sep 03, 2007 10:16 pm

hey guys that is all very handy to know thanks for the info.. i was looking into using a fuel injection system of an EA that is all ready to go onto the nissan motor and then throwing a turbo onto that setup..

i think i have to put in a mild cam..

is that maybe a more desirable option..

thanks Dan

Post by **PGS 4WD** » Tue Sep 04, 2007 9:34 pm

I've done a few using Holden Delco 808, they are cheaper to tune, it will need custom tuning to run turbo and Fords software is less available for that vintage. I have the software for AU onward that is flash based and Hoden from VN to current. I use a V8 loom and modify a number of things (without giving it all away). A couple of cars I've done in this way have done multiple Vic Winch, Ateco and Outback without a problem.
Joel

Post by **MrMaxi** » Wed Sep 05, 2007 11:37 am

Any pics of a turboed carby TB42 on gas or dual fuel ? Would one use a top hat for that ?

Post by **PGS 4WD** » Wed Sep 05, 2007 9:59 pm

I'd fully box the carby for the reasons mentioned earlier, pressure trying tom sqeeze the fuel out the throttle shafts and seals.

Joel

Post by **MrMaxi** » Sat Sep 08, 2007 6:00 pm

Just curious whether one of these top hats would suit a low boost app on a TB42 carb running duel fuel, I've seen a charger with a hemi 6 with something like thisat a car show, running a super charger

http://cgi.ebay.com/ebaymotors/Blow-Thr ... enameZWD4V
View user's profile Send private message

Post by **PGS 4WD** » Sun Sep 09, 2007 7:52 am

It can work but if you have a 300k carby with play in the butterfly shafts you may end up spraying fuel out the shafts. Some carby joints can put positive seals on the shafts for correct sealing.

Joel

Outer Limits 4x4 Board

gq petrol turbo, carby gas

gq petrol turbo, carby gas

Who is online