xhaust - am I getting ripped??

Post by **ash_on_mtb** » Mon Sep 17, 2007 6:52 am

How's this....?

91 80 series, 4.2d

To do a new exhaust for it, supplied and fitted, 2.5" 'sports' system and extractors, all new, muffler and res,

$1500...

Is that even in the ballpark of realistic...? (because it sure as $hit isn't for me...!!)

Whats the story with those Beaudesert ones I see many people have? Are they a kit form, DIY or what?? They haven't gotten back to me to find out.

Cheers all.

Post by **Daisy** » Mon Sep 17, 2007 7:21 am

definitely too much.

ring around man.

Post by **Dzltec** » Mon Sep 17, 2007 9:02 am

A Beaudesert full system will set you back 1300 inc gst. How long do you think it will take to fit, thats where the balance will be.

Andy

Post by **HotFourOk** » Mon Sep 17, 2007 9:05 am

I had a 2.5" turbo back system installed, with new dump pipe, stainless flex bellows and lukey muffler for $500. Awesome job too!

Post by **g35me** » Mon Sep 17, 2007 10:45 am

I paid $800 for cat back 2.5inch new resonator and muffler. So $1500 for extractors and cats on top is about right IMO.

Post by **dogbreath_48** » Mon Sep 17, 2007 11:10 am

I was quoted $1000+gst for a 3" turbo back inc. SS flex joint and 1 straight-through muffler, with flanged joins throughout.

Is that reasonable?

-Stu

Post by **Guy** » Mon Sep 17, 2007 11:11 am

I had extractors and 2.5 inch system put on my GU for about $700. (origional cat reused) with new flanges that didnt constrict to just over 65mm like the factory setup.

Post by DK » Mon Sep 17, 2007 6:48 pm

I paid $250 for a 2.5" from the turbo back straight through no muffler.

Website · Post by **cooter** » Mon Sep 17, 2007 6:51 pm

i paid 300 for a 2.5 sys with 2.75 inch turbo muffler and a 2.75 in tail pipe
not long ago at rutherford

Post by **hulsty** » Mon Sep 17, 2007 6:54 pm

Just this arvo I book my middy in for a 2.5'' system with straight through muffler, fitting of my extractors, $360 including new gasket and bolts

cheers

Post by **Cruza62** » Mon Sep 17, 2007 6:58 pm

I'm making my exhaust and its costing sweet FA....
for the price that most people have paid they could have bought the tools to do the job and made their own too.. maybe that's what you should look into, at the end of the day it's just a bit of pipe with bends which you can buy.

Post by **chunks** » Mon Sep 17, 2007 7:11 pm

Cruza62 wrote:I'm making my exhaust and its costing sweet FA....
for the price that most people have paid they could have bought the tools to do the job and made their own too.. maybe that's what you should look into, at the end of the day it's just a bit of pipe with bends which you can buy.

It depends if you have the skills or not to do it properly, i have seen some dreadful home fabrication jobs over the years...but then again i have seen some very good ones too!

Post by **chunderlicious** » Mon Sep 17, 2007 7:37 pm

i got extractors fitted and a 2.5 inch exhaust fitted for $300 and that had a muffler and needed a Y pipe made.

Outer Limits 4x4 Board

xhaust - am I getting ripped??

xhaust - am I getting ripped??

exhaust

Re: exhaust

Who is online