Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

soa (spring over axel)

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 2
Joined: Sat Nov 03, 2007 1:11 pm
Location: melbourne

soa (spring over axel)

Post by 60inDEISEL »

hey guys im a newbie to this forum and i have a 60 wagon and im currently rippin the diffs out to do a spring over conversion. just wonderin if any of you had done it and could tell me how much angle the pinion of the diffs need to be set at as aposed to stock...front/rear? and also whether the tail shafts need to be lengthened,if so how much...front/rear.
Top
Posts: 675
Joined: Sat Dec 17, 2005 10:06 pm
Location: campbelltown

Post by Nat84 »

hi have a soa 60 but i got the diffs already done and just bolted them it

as for springs etc all stock and i didn't need to do anything with the the tailshafts

Image
Tires are like boobs, they always look big until you have played with them for a while, then you just want a bigger set
Top
Posts: 57
Joined: Wed Dec 14, 2005 8:57 pm
Location: shoalhaven nsw

Post by T-rex »

the front must be kept stock, or you will mess up your castor. the only way you can move it is to cut and rotate your knuckles. but most of the time you can get away with out doing it. (saggy old stock springs)
Top
Posts: 238
Joined: Sun May 07, 2006 7:37 pm
Location: Pakenham

Post by seaeagle »

T-rex wrote:but most of the time you can get away with out doing it. (saggy old stock springs)
do you meen you dont have to cut the diff?
would there be to much angle on the shafts if ya didnt?
Top
Posts: 17
Joined: Wed May 09, 2007 1:53 pm
Location: MELBOURNE

Post by BADFJ »

Depends how saggy your front springs are, I've got a 40 with SOA, front springs were that saggy they started to invert, have put in a set of 2nd hand front springs and the front has lifted approx 1". Now have to get 60 series double cardan front drive shaft and get it lengthened as the front uni angle is stuffed. No cut and turn done, may even need castor wedges under the spring packs as well.
'78 40 series SOA, Pwr Steer, 4WDiscs, 38" Swampers. Ext W/base, 4wdicsc, Metal-Tech Cage, race seats/harnesses etc etc.
'88 60 series diesel.
Top
Posts: 567
Joined: Fri Jul 20, 2007 7:37 am
Location: Panama

Contact:
Contact Tapage

Post by Tapage »

The C&T procedure depends much in your lift .. with flat spring and SO you are getting aprox 6" of lift ..

I recomend C&T but know many persond that drive and use the cruisers SO without it ..

Usually you rotate from 8 up to 12degrees .. depending on your exact setup ..

In my case with 2.5 OME and SR rotate 12degrees .. and feel I get little short of caster .. anycase.
HJ-60 2H-T Intercoled [url=http://4x4panama.com/foros/viewtopic.php?t=2770]Tencha[/url]
HDJ-80 1HD-T Stock so far " Marilu "
Panama
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 125 guests