G'Day all,
Yesterday on a fishing trip up the mountains I noticed a vibration on turning corners so I checked the hubs and found them loose.
Has anyone else done the bearings in their Feroza? I am wondering where you got them, how much they are likely to cost and were there any tricky bits to it?
I have done bearings in other cars before but not one with locking hubs.
Any help would be much appreciated!
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Wheel Bearings
Moderator: Tiny
Wheel Bearings
On boooooost!!
Mine were replaced under warranty on the front left- you could wobble the wheel a good 10-20mm! (the funny part was it seemed to drive OK though)
I can Email the section from the manual on the front hubs- just PM me with your Email address. It's just under 3Mb so make sure your Email account can handle files that big (eg Hotmail won't)
I can Email the section from the manual on the front hubs- just PM me with your Email address. It's just under 3Mb so make sure your Email account can handle files that big (eg Hotmail won't)
David
Croz... check Daihatsu genuine parts first... I found with a clutch that the genuine article was about $90 cheaper than Repco aftermarket.
Man your car must have been driven by an old lady before you got it.... as soon as it saw some dirt it seems to be getting a few glitches... G
ood luck with it and be sure to be ready for December 20th....
Man your car must have been driven by an old lady before you got it.... as soon as it saw some dirt it seems to be getting a few glitches... G
ood luck with it and be sure to be ready for December 20th....
Message content not approved for consumption by children or easily damaged psyches. If accidentally exposed, flush eyes with cold water and induce vomiting. If irritation persists, sit quietly and watch SBS.
First thing i'd do is pull the hubs off and check they're OK...it's a pretty straight forward job...just need an allen key and a 10(?)mm spanner....also a pair of circlip pliers...but a screwdriver and a mate will do the same job for much cheaper than buying the tool.
Everything is pretty logical. If you're not confident, bring it over this Sunday and we should be able to sort it in under an hour...I found similar prob with the Zook when I got her. Heaps of degreaser, a bit of scrubbing at the rust, some new grease and she's now as good as new.
If it is actually the wheel bearings, I believe they are adjustable...so a bit of grease and a clean up should sort the problem...worth checking b4 you spend your hard-earned.
Everything is pretty logical. If you're not confident, bring it over this Sunday and we should be able to sort it in under an hour...I found similar prob with the Zook when I got her. Heaps of degreaser, a bit of scrubbing at the rust, some new grease and she's now as good as new.
If it is actually the wheel bearings, I believe they are adjustable...so a bit of grease and a clean up should sort the problem...worth checking b4 you spend your hard-earned.
bru21 wrote:What happens in goat, stays in goat!
Well it was certainly the wheel bearings, but there was no way a clean up and some grease was gonna fix that.... I took a foto of the left one after what appeared to be half the Cox's river finished flowing out of the race. I'll put it up soon.
There was evidence of heat scoring especially on the left, which was worse. Its a pretty sinple job, but look out for the bolts that hold in the lock/free dial, they appear to be fairly soft in the head (like some i know).
New bearings were $74 per hub including the seal.
The hardest part of the whole job was working out the fact that the dick in the parts store i bought them from gave me the wrong inner bearings, they are 3mm too narrow. They looked exactly the same as the shit covered ones i pulled out but once i cleaned the crap off the old ones and put them side to side it was obvious. this is of course only after three hours of trying to adjust them to fit! Anyways, someone is gonna get an irate phone call this morning when their shop opens!!
If all goes well it should be done this arvo when i finish work..
There was evidence of heat scoring especially on the left, which was worse. Its a pretty sinple job, but look out for the bolts that hold in the lock/free dial, they appear to be fairly soft in the head (like some i know).
New bearings were $74 per hub including the seal.
The hardest part of the whole job was working out the fact that the dick in the parts store i bought them from gave me the wrong inner bearings, they are 3mm too narrow. They looked exactly the same as the shit covered ones i pulled out but once i cleaned the crap off the old ones and put them side to side it was obvious. this is of course only after three hours of trying to adjust them to fit! Anyways, someone is gonna get an irate phone call this morning when their shop opens!!
If all goes well it should be done this arvo when i finish work..
On boooooost!!
Who is online
Users browsing this forum: No registered users and 4 guests