Drove it down to the carwash to clean it up a bit, was getting quite a few looks including a classic doube take followed by "what the f#ck?" from a guy driving a Terios
Pic with the new meats on :
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Got Meat?
Moderator: Tiny
Got Meat?
Put the 31s on the rig today in prep for tomorrows body lift. They rub a lot close to full lock, need those extra 2" !!! The rear ones also stick out from the guards just a tad...may do something about that..not sure what yet..
Drove it down to the carwash to clean it up a bit, was getting quite a few looks including a classic doube take followed by "what the f#ck?" from a guy driving a Terios
Pic with the new meats on :
Drove it down to the carwash to clean it up a bit, was getting quite a few looks including a classic doube take followed by "what the f#ck?" from a guy driving a Terios
Pic with the new meats on :
Looks Great 
Good luck with the body lift. Don't forget the brake lines and steering column. The brake lines bend down from their mount by the master cylinder to give you a bit of extra when jacking the body up. I didn't split one or have any problems once I'd done the lift.
Just lifted one quarter at a time using scissor jack ontop of the wheels
Yeah...in answer to your other thread.....I did the bodgy 2" lift using 50mm box tube cut into square blocks and used high tensile bolts.....which were a real bitch to take off when I did the conversion. (I actually helped remove them - unlike the rest of the conversion which Moose did) Also, the holes in the blocks were the same diameter as the bolts....ie... no give !!
The wheels scrubbed up well ! I note that they stick out from the guards at the rear, I didn't have that problem as I had a modified Vitara rear diff....50mm narrower....also had the 3/4 elliptical suspension (Don't do that !!)
Cheers
Good luck with the body lift. Don't forget the brake lines and steering column. The brake lines bend down from their mount by the master cylinder to give you a bit of extra when jacking the body up. I didn't split one or have any problems once I'd done the lift.
Just lifted one quarter at a time using scissor jack ontop of the wheels
Yeah...in answer to your other thread.....I did the bodgy 2" lift using 50mm box tube cut into square blocks and used high tensile bolts.....which were a real bitch to take off when I did the conversion. (I actually helped remove them - unlike the rest of the conversion which Moose did) Also, the holes in the blocks were the same diameter as the bolts....ie... no give !!
The wheels scrubbed up well ! I note that they stick out from the guards at the rear, I didn't have that problem as I had a modified Vitara rear diff....50mm narrower....also had the 3/4 elliptical suspension (Don't do that !!)
Cheers
[color=orange] BESTY [/color]
GU4800
GU4800
Ferozious..you have aroused my curiousity...what was this modified rear vitara diff you used? What ratio did it run? And did you put a locker in it? I'm thinking you would have had to have modified spring and shock mounts on the axle, as well as the rear driveshaft? Did it rub with the 31x105s? Did you use the Feroza spring?
Beware.....Curiosity killed the cat !! 
I used a standard Vitara diff with 5.17 centre.....had the ability to lock it easily...but didn't.
I used it after blowing my rear diff.. :( ..ease of bit to get, lower cost factor (plus ability to lock it)..
..that's why it happened. But at the same time...also did 3/4 elliptical suspension. The tail shaft was very easy to modify....<$100. (North Melb Shafts !)
I don't recommend you swap one into yours....just wait for some Hilux axles !
I used a standard Vitara diff with 5.17 centre.....had the ability to lock it easily...but didn't.
I used it after blowing my rear diff.. :( ..ease of bit to get, lower cost factor (plus ability to lock it)..
..that's why it happened. But at the same time...also did 3/4 elliptical suspension. The tail shaft was very easy to modify....<$100. (North Melb Shafts !)
I don't recommend you swap one into yours....just wait for some Hilux axles !
[color=orange] BESTY [/color]
GU4800
GU4800
Who is online
Users browsing this forum: No registered users and 0 guests