Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Install of CrMo Axles

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Install of CrMo Axles

Post by just cruizin' »

Got some u-beaut axles to install and am unsure of the process due to having 26 spline internals. I know I need the side gears from a rear diff. I have a rear diff centre with an Air Locker :) , will this bolt straight in or do the centres normally spin opposite directions? :?

If it doesn't suit the front I'll just use it in the rear so it won't go to waste :armsup:
;)
Top
Posts: 7345
Joined: Wed Jun 02, 2004 3:29 pm
Location: Melbourne

Contact:
Contact Gwagensteve

Post by Gwagensteve »

The rear arb set up will go straight in the front.

Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Top
Posts: 335
Joined: Sat Aug 05, 2006 11:21 pm
Location: Sunshine Coast

Post by Taff »

stripped those diffs down to bare housings this arvo, you shoulda seen the rust inside the swivel hubs!!! must have been sitting in a creek for a few weeks. :roll: all good though, will clean up fine :cool:

The rear air locker should go straight in, but wont it be 3.7 ratio? Will the NT CW&P interchange with the WT or is a whole center swap?
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

That's what I'm unsure of, can I swap the whole centre or just the locker? Both diffs are WT so 3.7.
;)
Top
Posts: 7345
Joined: Wed Jun 02, 2004 3:29 pm
Location: Melbourne

Contact:
Contact Gwagensteve

Post by Gwagensteve »

The whole third member swaps AFAIK

Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Top
Posts: 242
Joined: Tue Oct 09, 2007 9:54 pm
Location: Brisbane

Post by ScrawnC »

Post us up some pics when your done Greg :armsup:
Top
User avatar
Dee
Posts: 2314
Joined: Thu Mar 10, 2005 1:35 pm
Location: Sunny Coast, QLD

Post by Dee »

sorry to hijack, but i'm about to do the exact same thing.
has anyone swapped the side gears in a front 22spl airlocker with the ones from a rear 26 spline to fit crmo's? pretty sure i read somehwere on here it was a straight swap...

Im bout to do this, but am a little worried about pulling the airlocker apart. I downloaded an exploded parts diagram, and I've pulled my standard rear centre apart to fit an auto locker before, is there much difference? Anything extra I should worry about/look out for?
Or should i just pay some apprentice at ARB 70 bucks an hour and let them worry about it?
All the gear, No idea...
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

I bought a front ARB locker just before these CrMo axles became available so when they did the first thing I did was contact ARB to see if the 26 spline side gears are available seperately and if they are a straight swap and they said YES on both counts. :armsup: :armsup:
My diff experience (apart from changing heaps of them) is: fitted two mini spools and an ARB and was easy enough so I don't think it's gonna be difficult to change the side gears..
ARB 26 spline
side gear part #131101
Splined side gear part # 131201
Jas.
Top
User avatar
Dee
Posts: 2314
Joined: Thu Mar 10, 2005 1:35 pm
Location: Sunny Coast, QLD

Post by Dee »

thanks mate, yeah i already got the part numbers... how much were they?
All the gear, No idea...
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

Dee wrote:thanks mate, yeah i already got the part numbers... how much were they?
No worries Brodie,
I didn't ask.. It'll be a while before I need them so I don't need to worry about it just yet. :lol:
I thrash my car but I'm not hard on it (mechanical sympathy) so even when the front is locked with MT 117 Extremes I don't think it will be breaking too many cv's.
Jas
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

Just to drag up my old thread

Got the axles and am finally fitting but have run into dramas

CV won't fit through the knuckle.

Rebuild the knuckle joint and know diff ball sits high in the knuckle meaning even a standard CV won't fit in?? Have I fitted the king pins wrong.
;)
Top
Posts: 7345
Joined: Wed Jun 02, 2004 3:29 pm
Location: Melbourne

Contact:
Contact Gwagensteve

Post by Gwagensteve »

Chromo CV's won't go through the knuckle - you have to remove the knuckle to fit them.

Yes, it sounds like you have something installed incorrectly, but without looking at it it's hard to tell what.

Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Top
Posts: 1908
Joined: Thu Aug 04, 2005 8:09 pm
Location: central queensland

Post by known 2 »

are chromo cv's and axels available for narrow tracks?
kaylee 2004 hdj78 RV. 33 mickey atz's, winchbar, 3i lift, 3i exhoust, spoties, roofracks and ufh. pimped interior .

86 lwb zook wt soa, 33's, locked, bard up, prety lights. monster tacho:/
Top
Posts: 7345
Joined: Wed Jun 02, 2004 3:29 pm
Location: Melbourne

Contact:
Contact Gwagensteve

Post by Gwagensteve »

No. You'd have to get the inner axle shortened. Probably cheaper to get a WT front axle housing.

Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

here's a pic

Image
;)
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

Image
;)
Top
Posts: 7345
Joined: Wed Jun 02, 2004 3:29 pm
Location: Melbourne

Contact:
Contact Gwagensteve

Post by Gwagensteve »

You haven't got the knuckle on upside down have you?

Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Top
Posts: 2066
Joined: Mon Jun 09, 2003 8:17 pm
Location: Gympie

Post by Rhett »

does the stock hi-steer give it away ;)
Its a wheelbase thing
Top
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

Uuuummmm nope, that's the right way. Other wise steering arm would be fighting with the springs. But you made me think.
;)
Top
User avatar
Guy
Posts: 10366
Joined: Thu Dec 12, 2002 8:43 am
Location: Wangaratta

Post by Guy »

just cruizin' wrote:Uuuummmm nope, that's the right way. Other wise steering arm would be fighting with the springs. But you made me think.
That is 100% the right way up ...

Image
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 6 guests