did a quick search but didn't reveal too much.
I'm putting a 96 disco 3.9 in my 86 rangie and obviously the temp senders are differant, in both thread size and resistance values.
essentially what i;m looking for is a sender the same thread as the disco one but with the resistance values of the range rover gauge, anyone have any luck finding one??
other options would be using a screw in adaptor to use the rr sender (will sit a fair bit higher though and wont be in the coolant flow as much as before, problem?)
or drilling and tapping the smaller disco thread to suit the larger rr sender (if theres enough meat around there?).
i want to keep running the 3.9L inlet manifold too, dont want to change back to the 3.5 one.
Just thought i'd try and get some info/ideas as i'd say a few people would have done this conversion before.
cheers,
Cal.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
temp sender disco to RR
Moderator: Micka
temp sender disco to RR
'86 Hiline, 3.9L, R380, Q78's, F&R Maxi's, Warn 8274
My impression is that the resistances of the gauge sender are similar, and also the hole sizes are similar but one is UNC or pipe or something and one is metric. This applies to 3.9 with V belts up to 93 anyway.
You haven't grabbed the choke light deactivator of the 3.5 by any chance? This sits on top of the manifold in front of the carbs.
The temp gauge sender usually , in a 3.5 and V belt 3.9 sits on the front of the manifold next to the thermo housing. It is a single wire.
Even on my Thor manifold there was plenty of meat to drill a hole for the sender.
Regards Philip A
You haven't grabbed the choke light deactivator of the 3.5 by any chance? This sits on top of the manifold in front of the carbs.
The temp gauge sender usually , in a 3.5 and V belt 3.9 sits on the front of the manifold next to the thermo housing. It is a single wire.
Even on my Thor manifold there was plenty of meat to drill a hole for the sender.
Regards Philip A
fair bit of differance in sender size, heres a pic-armbrup wrote:My impression is that the resistances of the gauge sender are similar, and also the hole sizes are similar but one is UNC or pipe or something and one is metric. This applies to 3.9 with V belts up to 93 anyway.
bigger rangie sender sits horizontal infront of the manifold (1986 EFI rangie)
Smaller disco( 96 serp) sender sits vertical next to the CTS on the pass side of the motor
this is the location of where the disco sender is ment to go-armbrup wrote:The temp gauge sender usually , in a 3.5 and V belt 3.9 sits on the front of the manifold next to the thermo housing. It is a single wire.
Even on my Thor manifold there was plenty of meat to drill a hole for the sender.
Regards Philip A
the easiest way it seems seeing i've had no luck finding compatible senders will be to tap my larger rangie sender in here, however i think its going to be borderline to whether there is enough metal around that rasied section to drill and tap(bearing in mind sender size differance from first pic).
Do you (or anyone else) have any pics of where you tapped yours in?
Cheers,
Cal.
'86 Hiline, 3.9L, R380, Q78's, F&R Maxi's, Warn 8274
Who is online
Users browsing this forum: No registered users and 32 guests