Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

ENgine coolant leak

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Post Reply
Posts: 224
Joined: Sun Jul 23, 2006 4:47 pm
Location: Cornubia

ENgine coolant leak

Post by Sean »

G'day,

I have a coolant leak in a lwb Vitara G16B, it uses a large amount of coolant in a single day, i have to add a fair amount of coolant each morning. I have pulled the cap off and cant see any bubbles in the coolant.

When the engine is running and lying under the vehicle you can see engine coolant dripping off the front diff. When looking from above you can see it dripping onto the alternator, then the water pump then onto the diff.

Can anyone direct my search as to where the leak may be?

Are the heads and blocks prone to cracking?

Cheers,
Sean
[quote="v840"]fat chicks actually [i]do[/i] give better head cause they're always hungry![/quote]
Posts: 696
Joined: Mon Jan 10, 2005 7:07 pm
Location: Greenbank

Post by zookimal »

Hopefully more simple and cheaper to fix than head or block. Unsure if that's common but have found G13 blocks handle plenty of abuse.

Check rad/heater hoses for pinhole sized leaks first. They will spray from the split hose and onto something else in the bay. I thought I'd split a head gasket a few years back as coolant appeared to be leaking from the block, but like you, no bubbles or oil in the coolant etc, but then realised a heater hose was split and spraying onto it.
-Mal

Zook 1, 2, 3 gone
Patrol - Wheels, engine and stuff
Posts: 224
Joined: Sun Jul 23, 2006 4:47 pm
Location: Cornubia

Post by Sean »

thanks i will check that, i forgot to mention that all the hoses looked OK, completely missed the heater core hoses though.

Cheers,
Sean
[quote="v840"]fat chicks actually [i]do[/i] give better head cause they're always hungry![/quote]
Posts: 19
Joined: Wed Jan 02, 2008 10:15 am
Location: melbourne, east suburbs

Post by chris.e »

Pull the front cover off the motor and check the waterpump, it has a coolant escape hole on the lower side of the shaft casting.
Posts: 459
Joined: Sat Jul 29, 2006 8:39 pm
Location: brisbane (boganhole)

Post by short stuff »

my gti motor was leaking at the front of the motor between the head and block but it had no bubbles or compresion loss we source the problem to be one of the head bolts was loose
Posts: 10
Joined: Fri Aug 17, 2007 8:01 pm
Location: NE Melbourne

Post by Phantomzook »

Had the same problem with mine 2 weeks ago. Replaced the two heater hoses then found the culprit was a small hose from the throttle body to the block above the alternator. It was at the throttle end but was running down on to the bottom heater hose. Access was tight I’d recommend taking off the black plastic cover near the efi print 3 bolts. From the side/under take off the triangular black mount 2 high bolts and loosen the bottom and swing out. The hose had a few bends in it but after a small search at repco they found something close off a landcrusier $10 :)
Post Reply

Who is online

Users browsing this forum: No registered users and 62 guests