need reduction gears in mq and want to fit gq coil diffs???

[nick bj40]

i have some gq coil diffs i picked up cheap and want to put under my mq but need a rear center tail shaft is anything i am saying making any sence or posible

can i fit a gq transfer to a mq gear box or can a gq gear box to a sd33??

[SWBMQCraig]

Hey im just new to this but was reading a thread about that the other week have a search through the bible pretty sure it was in there,
but basically it was saying that it was very hard to do cos of the main drive line moving across you would have to move everything and
also the shifter would then be in the wrong spot and the transmission mounts etc

is it possible just to change the centres across to get the ratio down?

Cheers Craig

[VXPSI]

gq diffs are abit wider aswell then the mq

[chunderlicious]

the centre diff is fine, wont put the shaft out enough t cause too much trouble. they are wider, quite a bit wider so they may not be legal without big gaurds.

you going coils or leaves? the only real reason for the change would be coils.

[nick bj40]

ok i know the gq diffs are wider and i do want to go coils i havent been sucesful in searches lately they just dont find anything but i'll go though the bible again tonite

chunder, i dont quite understand wat u are saying? are u saying to just use the mq gear/trans?? can you elaberate plz mate

p.s thanks guys nick.

[WICKED]

GQ coil diffs are roughly 5-6 inchs wider than MQ.
GQ Leafs diffs are approx. 30mm wider than MQ.

There is NO reduction gears for MQ T-Case's, unless, they are custom made. A mate has some but they are the only I've ever heard of.

You could do twin divorced MQ T-Case's.

As for the GQ Box &/or T-case I have know idea.

GQ Coil diffs under a leaf sprung MQ is not easy. There is a few options -

Outboard the springs 2inchs off the chassis.
Have the drivers spring pack sitting on the diff centre and the passanger approx 50mm of the housing.
Or you could try and nortch the housing the fit the leaves.

Coils would be easyer and more legal. But trying to fit a Panhard bar could be a mission with the steering.

I have a 60's LandCruiser case (Driver side out put) but I'll be running a GQ rear diff (centre out put) I can't see it being a big problem but mine is not a Daily Driver.

[RMP&O]

GQ coil diffs are roughly 5-6 inchs wider than MQ.
GQ Leafs diffs are approx. 30mm wider than MQ.

There is NO reduction gears for MQ T-Case's, unless, they are custom made. A mate has some but they are the only I've ever heard of.

You could do twin divorced MQ T-Case's.

As for the GQ Box &/or T-case I have know idea.

GQ Coil diffs under a leaf sprung MQ is not easy. There is a few options -

Outboard the springs 2inchs off the chassis.
Have the drivers spring pack sitting on the diff centre and the passanger approx 50mm of the housing.
Or you could try and nortch the housing the fit the leaves.

Coils would be easyer and more legal. But trying to fit a Panhard bar could be a mission with the steering.

I have a 60's LandCruiser case (Driver side out put) but I'll be running a GQ rear diff (centre out put) I can't see it being a big problem but mine is not a Daily Driver.

duel MQ t-cases = a go especially if you have an LWB!

no reduction gears for MQ's because they don't fit in the gear box. No room for them unless you want something like 20% reduction. Not much point in that...

panhard in front is a bitch for sure....mine was!

Go coils, GQ diffs I say. But we don't have the legal issues here in the USA you do over there in Aus.

[nick bj40]

sorry guys i wasnt very through with my info but i was planing to 4 link front, a frame rear or 4link front and rear

but is where im a bit stuck is the rear centre drive shaft i dont think the mq gear box is suitable but not sure if the gq box can mate up with my sd33

i think i might have 2 go auto but dont want to go that expensive

[dattopimp]

mate, you have an MQ...its gonna be expensive any way you go

[rvh96]

probably be cheaper and a hole lot easier to just buy a gq

[macca81]

im fairly sure a GQ box can be mated up to a SD33, but you wouldbe better off putting a TD42 with box and case attached in. that will go with the GQ axles just fine. i know a block who has a MQ ute with the GQ running gear, bloody nice. his is leaf sprung tho

[q_ship]

mate, you have an MQ...its gonna be expensive any way you go

x 2

what do u wanna achieve? seems a good idea but the fab work involved would far out way the end result. as some has said buy a gq. cheap way to go mate imo

[grimbo]

what you are planning to do has been done before by these guys from Nissan and they called it a GQ

[nick bj40]

yer good point grimbo but i didnt want 2 be another gq on the tracks i like my mq and i have gq diffs and is what i wanted to know is can the gq gear box be mated up to the sd33??

sorry for the confusion...

[Big Red Toy]

If you really want to stick with the Mq, get yourself a 5speed turbo diesel box & the 4.6 diff gears out of the petrol L29 patrol.
Is the easiest way to get low gearing using stock parts

As for gq diffs under the mq, Can you do the fabrication work yourself? If so then go for it, if not sell it & buy a Gq

I've had 2 mq/mks & went the move to a lwb gq, shits all over it!

Andrew

[dattopimp]

If you really want to stick with the Mq, get yourself a 5speed turbo diesel box & the 4.6 diff gears out of the petrol L29 patrol.
Is the easiest way to get low gearing using stock parts

As for gq diffs under the mq, Can you do the fabrication work yourself? If so then go for it, if not sell it & buy a Gq

I've had 2 mq/mks & went the move to a lwb gq, shits all over it!

Andrew

The NA diesel 5 speed has the lowest first gear, equal with the L28? your diff gears...whatever you can get inthe gq diffs. If you got a divorced transfer you would probably have more options.

I've been toying with the idea of selling my MK and gettin a GQ but...i've just spent too much money on it and don't wanna start again