Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Hilux body lift

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 42
Joined: Wed Apr 16, 2008 1:10 am
Location: Perth

Hilux body lift

Post by Grimey »

I tried to search the forums, but it doesnt seem to be working for me. so sorry if im missed the right thread. im wondering what exactly is needed to lift a 5L-E hilux dualcab 2 inches, do i need to start lifting the gear box and transfer case? i really dont know haha or is it a matter of putting mounts?

whats the normal material for mounts? is it polyethalene?
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

The bodylift lifts just that the body, the drive train is unaffected. You will to lower the radiator and extend the steering, though I think this model has an extendable column. Everything else is fine, may have to open up the tunnel holes for the shifters too.
;)
Posts: 43
Joined: Tue Apr 18, 2006 6:41 pm
Location: lismore

Post by old mate »

I,ve got hardened nylon for mine i bought from the bearing shop around the corner and longer high tensile bolts. Cost me about $110 all up for a dualcab, Hardest part was raising my bullbar to suit and extending the steering shaft. Make sure you keep a eye on the brake lines and clutch lines when your lifting it up.
Posts: 3224
Joined: Thu Apr 15, 2004 9:36 pm
Location: Lost in the Cleland fog!

Post by ferrit »

to be technially legal, you need to use either a solid metal, or a machinable plastic (polythene, Nylon etc) with a crush sleeve. Although the chances of you being able to distort 50mm of nylon (we've put some 100mx50m rods of the stuff under the drill rig feet and lifted a 15T drill rig off the ground with them!) are pretty low- thats what the law requires.

you may need to extend your shifters 2" too to keep them in the same place- thats optional though, you do need to either enlarge the hole in the floor or bend the low range lever to make it work tho
2005 HDJ100 Manual, ARB bar, XD9000 winch, ARB rooftop tent + awning, Drawers, Engel, 2" OME lift, 285/75R16 KM2's, iCom, HID XGT's.
Posts: 42
Joined: Wed Apr 16, 2008 1:10 am
Location: Perth

Post by Grimey »

cheers for the help, i sort of knew about the 4L problem, but my mate was talking about lifting his gear box and something else but i guess that was because of his 3" suspension(thats for a swb patrol)
Posts: 1889
Joined: Mon Sep 20, 2004 10:23 pm
Location: Brisbane

Post by just cruizin' »

You could lift your gearbox and transfer a little but this should be done to gain clearance under the vehicle if they hang down some what, I wouldn't lift them to make the shifter work easier as you are losing some of he benifit of the Body lift, that is to gain body clearance with out raising the centre of gravity too much
;)
Posts: 166
Joined: Fri Sep 19, 2008 6:19 pm
Location: New Zealand

Post by xxxhilux »

how far can u raise up the gbox a transfer before u have problems with drive shafts?
http://www.outerlimits4x4.com/ftopic154894.php
Posts: 2072
Joined: Sun Feb 11, 2007 4:50 pm
Location: Hobart

Post by macca81 »

xxxhilux wrote:how far can u raise up the gbox a transfer before u have problems with drive shafts?
same amount as you can lift the suspension normaly i would think...
[quote="Barnsey"]
Bronwyn Bishop does it for me.[/quote]
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest