Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
GU vibration after clutch replacement
GU vibration after clutch replacement
Hi Guys
I have a strange problem with my 5th gear.
2000 GU II 4.2 Man
Everything was great and needed a new clutch.
Got a 4Terrain put in a few weeks ago and everything seemed ok.
At idle there is a slight vibration but not too much to worry about.
I had not been on a freeway for a while and driving around town is fine.
Got onto the freeway and noticed that 5th vibrates when under load.
Do you think this could be caused by the new clutch?
A possible 5th gear issue woken up by having the gearbox out?
Or somthing the mechanic has done?
If for some reason it is the clutch, would there be any way of covering the labour to get the box out with the clutch warranty?
Thanks for any help
Cheers
Eric
I have a strange problem with my 5th gear.
2000 GU II 4.2 Man
Everything was great and needed a new clutch.
Got a 4Terrain put in a few weeks ago and everything seemed ok.
At idle there is a slight vibration but not too much to worry about.
I had not been on a freeway for a while and driving around town is fine.
Got onto the freeway and noticed that 5th vibrates when under load.
Do you think this could be caused by the new clutch?
A possible 5th gear issue woken up by having the gearbox out?
Or somthing the mechanic has done?
If for some reason it is the clutch, would there be any way of covering the labour to get the box out with the clutch warranty?
Thanks for any help
Cheers
Eric
2000 GU II 4.2TD
Mate... if the problem wasent there when u drove in but is there when u drove out then u should go back to the person who did the work and tell them about the problem... asap... dont leave it for weeks and hope the problem goes away
88 GQ SWB 5''SUS LIFT 60MM BODY LIFT, FRONT LOKKA, NOW WITH 304, ...... :D
www.roverpark.com
www.roverpark.com
Really? bugger, i didnt read that anywhere when deciding between the 4terain and safari.
The tail shaft was on the cards soon to have the unis done and a balance.
Could the clutch or tailshaft cause this only in 5th gear?
Im hoping so because I dont want it to be the gear box
If its the clutch I dont know if I can handle that on a long trip.
cheers
Eric
The tail shaft was on the cards soon to have the unis done and a balance.
Could the clutch or tailshaft cause this only in 5th gear?
Im hoping so because I dont want it to be the gear box
If its the clutch I dont know if I can handle that on a long trip.
cheers
Eric
2000 GU II 4.2TD
well depends if its speed related or gear related. generaly if it where the clutch it would be there in all gears because its always spinning at the same speed. although would be eaisier to notice in 5th because its quiter and smoother. most likely t/shaft is out of alignment and only notice at high speeds. could also be phantom vibration!!!! people tend to notice/worry about there cars alot more after work is done on them! every little noise/bang/squeal/vibration makes people paranoid to the point of thinking s**ts hit the fan and the worlds gonna end. depends how bad the vibration is. maybe check the g/box mounts are tight as well
Hi
I know what you mean by phantom. You do listen to things alot more when work has been done.
This is to the point that I would almost not use 5th.
The mechanic changed the unis today. They were on the list to do anyway.
Not sure if it improved a tiny bit, but its still there.
See how we go tomorrow.
cheers
I know what you mean by phantom. You do listen to things alot more when work has been done.
This is to the point that I would almost not use 5th.
The mechanic changed the unis today. They were on the list to do anyway.
Not sure if it improved a tiny bit, but its still there.
See how we go tomorrow.
cheers
2000 GU II 4.2TD
Hi Guys
Replacing the unis helped a little. So the next day we got the tail shaft balanced also, which did not help.
Also replaced the Slave.
My mechanic rang clutch industries again and spoke to a different person.
They described the problem to my mechanic exactly. They then said it was most likely the preasure plate.
Now we need to take it all out and let them look at it. They wil then give us the money back on a new one.
Only problem is they will only give about $200 to my mechanic towards labour.
Cheers
Eric
Replacing the unis helped a little. So the next day we got the tail shaft balanced also, which did not help.
Also replaced the Slave.
My mechanic rang clutch industries again and spoke to a different person.
They described the problem to my mechanic exactly. They then said it was most likely the preasure plate.
Now we need to take it all out and let them look at it. They wil then give us the money back on a new one.
Only problem is they will only give about $200 to my mechanic towards labour.
Cheers
Eric
2000 GU II 4.2TD
Who is online
Users browsing this forum: No registered users and 86 guests