Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

hj75 gearbox into hzj

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 278
Joined: Fri Nov 30, 2007 4:14 pm
Location: bunbury

hj75 gearbox into hzj

Post by troopy94 »

It looks like im up for a gearbox rebuild on my hzj75 troopy and have been offered another box from a hj75 for free.What i would like to know is can the hj box be fitted to my hzj.
Top
Posts: 309
Joined: Sun Apr 24, 2005 8:20 pm

Post by Thommo 73 »

no
1uzed and no home for it
Top
Posts: 278
Joined: Fri Nov 30, 2007 4:14 pm
Location: bunbury

Post by troopy94 »

Ok thanks for that i was told that if you run the hj clutch it would work but he wasnt 100% sure
Top
Posts: 3038
Joined: Thu Aug 05, 2004 10:06 pm
Location: VIC

Post by dogbreath_48 »

Thommo 73 wrote:no
Are you sure? When i was looking at putting a 1HZ in my HJ75 i thought it was possible with the correct bellhousing/input shaft combo?
Tetanus rolling on 37's
Top
Posts: 1715
Joined: Tue Sep 06, 2005 8:38 pm
Location: at my wits end

Post by RED60 »

T94, get the freeby then if it doesnt fit swap it for sumthing that does.. or if it does fit do a swap thread on here and enlighten us all.... :cool: :cool:
Show me the money..SHOW ME THE MONEY
Top
Posts: 97
Joined: Mon Jun 06, 2005 6:33 pm

box

Post by tobie »

yes it will fit

change bellhousings
run the 1hz clutch but the 2h pressure plate
you will have to machine a spacer to run where the spigot bearing goes to take the input shaft as the early box has a shorter shaft from memory 15mm

they do fit i have done the swap, just measure the shafts and that will give u a indication of the spacer that has to be made
Top
Posts: 309
Joined: Sun Apr 24, 2005 8:20 pm

Post by Thommo 73 »

well if your going to that extreme anything will fit.
your better of getting yours rebuilt, get your freebie and sell it for 600 and put that towards the rebuild.
1uzed and no home for it
Top
Posts: 278
Joined: Fri Nov 30, 2007 4:14 pm
Location: bunbury

Post by troopy94 »

I will be pulling my box out soon then i will compare the 2 but machining up a spacer wont be a problem.I planned on replacing the clutch while the box was out anyway.Just wondering are the ratios of the 2 boxes the same?
Top
Posts: 701
Joined: Tue Feb 03, 2004 3:04 pm
Location: Melbourne

Post by 80UTE »

troopy94 wrote:I will be pulling my box out soon then i will compare the 2 but machining up a spacer wont be a problem.I planned on replacing the clutch while the box was out anyway.Just wondering are the ratios of the 2 boxes the same?
The ratios are the same to fit the 2H/3F box i machined the bellhousing ( from memory 10mm off the engine block side and 5mm off the gearbox side ) with a 2H clutch plate and off it went. The 2H/3F boxes are much better ( the gear form and heat treatment was better ) and they last much longer.


Wally
THERES ONLY ONE SUBSTITUTE FOR CUBES AND THATS MORE and if you want more inchs stroke it !!!!!!!!!!!
Top
Posts: 278
Joined: Fri Nov 30, 2007 4:14 pm
Location: bunbury

Post by troopy94 »

I was driving the troopy out to a mates workshop to pull the box out and the noise slowly got louder and could be heard in all 5 gears so it turned out that i had a collapsed pinion bearing in the rear diff.Id like to thank those for their advice and an apology for the misdiagnosis
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 8 guests