Has anyone ever put a GU dash into a GQ?? Will it fit?
Also will it be legal?
Am thinking of doing it and just thought i'd ask if anyone has done it.
Also am looking for fuel pump for carby 4.2 patrol. Anyone??
thanks
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
GU Dash into GQ
dont listen to the neigh sayers... get to your wrecker and run the tape measure around a GUs dash and then compare it to the size of the gq...
dont expect it to be a straight fit and to just BOLT up, but mounting points can always be acheived if you have a welder...
and then there are the bits that align to the door trim, you would have to think about how to finish them.
good to see someone thinking differently
dont expect it to be a straight fit and to just BOLT up, but mounting points can always be acheived if you have a welder...
and then there are the bits that align to the door trim, you would have to think about how to finish them.
good to see someone thinking differently
A speed camera would have prevented that!
Question to be asked in all seriousness...
..what are you hoping to achieve? I believe that the GU dash maybe wider, are the instruments capable of being hooked up to the GQ wiring..voltage..amps...connectors, speedo drive cable sender.
I think it will be quite complex and in the not worth it. Maybe wrong but perhaps think about improving the guages or look of the GQ dash. Dash board pod to house instruments or other functions.
Mulisha designed some white instrument faces that looked cool. HE hasn't been around for a while though and maybe not a current member.
..what are you hoping to achieve? I believe that the GU dash maybe wider, are the instruments capable of being hooked up to the GQ wiring..voltage..amps...connectors, speedo drive cable sender.
I think it will be quite complex and in the not worth it. Maybe wrong but perhaps think about improving the guages or look of the GQ dash. Dash board pod to house instruments or other functions.
Mulisha designed some white instrument faces that looked cool. HE hasn't been around for a while though and maybe not a current member.
I am the Nightrider! I am the chosen one. The mighty hand of vengeance, sent down to strike the unroadworthy!
Yeah mate just be a sheep and follow every other boring person and dont try anything different cause it may be a bit hard. 
I think there all missing the point. Its no different to replacing the motor with something different. but no-one poo poos that idea. If its something you feel like doing then just make it work.
I think it would be cool not having what everyone else has, will probably be difficult with the wiring side of it but if you can do it, it will be unique.
If no-one did anything different we would all be driving the same boring something.
I think there all missing the point. Its no different to replacing the motor with something different. but no-one poo poos that idea. If its something you feel like doing then just make it work.
I think it would be cool not having what everyone else has, will probably be difficult with the wiring side of it but if you can do it, it will be unique.
If no-one did anything different we would all be driving the same boring something.
im guessing if its the same engine like td42 it should be ok but i think that all the nissan senders are the same.. water temp oil pressure wise so it should be able to be wired up but other wise buy a few senders.. i got oil press water temp ones for my rx7 for like 15bux..
i have thought about remoulding my gq dash and changing to speco guages or something just to be different and give it a go.. if i fail i buy another dash..
i rekon give it a shot.. cut it down you will have to move the air vents maybe.. buy you could get it plastic welded in place the re wrap the dash in vynil so you cant see any cuts..and make some mounts..
if its what you want to do go for it you may find its easier then you think.. i find i can do most things if i give it a go..
i have thought about remoulding my gq dash and changing to speco guages or something just to be different and give it a go.. if i fail i buy another dash..
i rekon give it a shot.. cut it down you will have to move the air vents maybe.. buy you could get it plastic welded in place the re wrap the dash in vynil so you cant see any cuts..and make some mounts..
if its what you want to do go for it you may find its easier then you think.. i find i can do most things if i give it a go..
Well you type that with rolly eyes. But really I dont think the GU is much wider if any on the inside. Its just fat in the panels. I do know the rear wheel arches are the same as a GU/GQ which are also pretty much the same as 80/100series.mickyd555 wrote:yeh man, it will slot straight in. Nissan just changed the look of the outside
THOUGHT FOR THE DAY....
I got curious one day as to seeing a GQ with a GU interior...I for one wouldn't mind seeing how it was to turn out.
Modifying almost anything on any vehicle is never easy or straightforward, and proving everyone else wrong sure is entertaining. How is it any different to, say, putting a vx commo interior into an old vn. Same shit different smell.
I had 2 mechanics frown on me and whinge bitch and nag about me wanting to put the commo v6 into my triton, how it was stupid, and a pain in the arse to work on, no room, blah blah blah. All because they'd seen a hilux done.....I proved them mofo's wrong
was heaps of room around the sides to work on it, and definately worth the gains...and fun
If your keen and can stick to the challenge then just f@#$&n do it
Modifying almost anything on any vehicle is never easy or straightforward, and proving everyone else wrong sure is entertaining. How is it any different to, say, putting a vx commo interior into an old vn. Same shit different smell.
I had 2 mechanics frown on me and whinge bitch and nag about me wanting to put the commo v6 into my triton, how it was stupid, and a pain in the arse to work on, no room, blah blah blah. All because they'd seen a hilux done.....I proved them mofo's wrong
was heaps of room around the sides to work on it, and definately worth the gains...and fun If your keen and can stick to the challenge then just f@#$&n do it
[quote="Ruffy"]P.S. woober woober is a technical term describing the audible tone emitted from harmonic air vibration.[/quote]
F/S Holden V6 auto to Mitsu kit incl exhaust for Triton conversion.
F/S Holden V6 auto to Mitsu kit incl exhaust for Triton conversion.
I for one much prefer the GQ dash - you can stick things on the flat bits - the area behind the grab rail is perfect for map books, telephone directories and so on. Sloping dashes are useless.
I feel better now. Might go out and put Armorall on my dash for a while
I feel better now. Might go out and put Armorall on my dash for a while
Burra Boy. 1x 89 LWB wagon, turbo, frozenboost IC, lots of stuff. 1X 90 leafie ute, AXT turbo, tough as nails and about as comfie...
Who is online
Users browsing this forum: No registered users and 9 guests