Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Leaky transfer case seal
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Leaky transfer case seal
Just a couple of quick questions for the experts. I have a HZJ75 ute with a leaky rear transfer case seal.
Can the seal be accessed from the rear after removing the yoke or does the bearing retainer need to be removed?
Is the Toyota seal good or is there a better “terrain tamer multi lip extra special magic seal” that I should use?
Is the nut easy to remove , the seal easy to pull out (and any thing else I’ve forgotten) or is a job better left to a mechanic.
Or
Should I put up with the leak?
Yep! I did search.
Any links, hints, pictures, comments appreciated.
Can the seal be accessed from the rear after removing the yoke or does the bearing retainer need to be removed?
Is the Toyota seal good or is there a better “terrain tamer multi lip extra special magic seal” that I should use?
Is the nut easy to remove , the seal easy to pull out (and any thing else I’ve forgotten) or is a job better left to a mechanic.
Or
Should I put up with the leak?
Yep! I did search.
Any links, hints, pictures, comments appreciated.
Resident Terrorist
You will probably find that the edge of the nut has been peened (probably not the correct term but thats what I call it) onto the shaft to lock it in place. You'll know what I mean when you look at it. Its to stop the nut coming undone. You'll need to get a small chisel and tap the peened section out so it clears the thread. Then it should be fairly easy to rattle undone. Make sure you re-peen the nut to the shaft when you've put it back together.Shadow wrote:Give it a crack firstozdave wrote:Sounds like I'll need a nut splitter and a new nut. Thanks for the replies. I will go with the genuine seal.
just drop your tailshaft and put a rattle gun on it, might just spin off.
I may have just had a bad one :(
on my fj45 couldnt do this cause it would crush the exhaust before it hit the chassis.Jacked wrote:socket with long breaker bar resting against the chassis and drop the clutch in gear. Dont remember if use foward or reverse gear through and slightly dangerous/dodgey
also, didn't try it cause its dodgy as fuck.
03 HDJ100R GXL / 94 FJ45-80
any rattle gun worth its name will be able to spin the nut regardless of the peened in section, unless the nut is stuck good n proper.RAY185 wrote:
You will probably find that the edge of the nut has been peened (probably not the correct term but thats what I call it) onto the shaft to lock it in place. You'll know what I mean when you look at it. Its to stop the nut coming undone. You'll need to get a small chisel and tap the peened section out so it clears the thread. Then it should be fairly easy to rattle undone. Make sure you re-peen the nut to the shaft when you've put it back together.
03 HDJ100R GXL / 94 FJ45-80
Resident Terrorist
9 times out of 10 this is true. I have come across quite a few now that simply wont rattle off untill the peened section is tapped out.Shadow wrote:any rattle gun worth its name will be able to spin the nut regardless of the peened in section, unless the nut is stuck good n proper.RAY185 wrote:
You will probably find that the edge of the nut has been peened (probably not the correct term but thats what I call it) onto the shaft to lock it in place. You'll know what I mean when you look at it. Its to stop the nut coming undone. You'll need to get a small chisel and tap the peened section out so it clears the thread. Then it should be fairly easy to rattle undone. Make sure you re-peen the nut to the shaft when you've put it back together.
x100. i dont even bother trying without bending the section back, have even stuffed the thread on a fwd cv joint because of it!RAY185 wrote:9 times out of 10 this is true. I have come across quite a few now that simply wont rattle off untill the peened section is tapped out.Shadow wrote:any rattle gun worth its name will be able to spin the nut regardless of the peened in section, unless the nut is stuck good n proper.RAY185 wrote:
You will probably find that the edge of the nut has been peened (probably not the correct term but thats what I call it) onto the shaft to lock it in place. You'll know what I mean when you look at it. Its to stop the nut coming undone. You'll need to get a small chisel and tap the peened section out so it clears the thread. Then it should be fairly easy to rattle undone. Make sure you re-peen the nut to the shaft when you've put it back together.
Who is online
Users browsing this forum: No registered users and 184 guests