Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

GQ CHEV 350 HEI ignition Cutting out !!!

For all things Electrical.

Moderator: -Scott-

Post Reply
Posts: 601
Joined: Mon May 24, 2004 9:50 am
Location: south eastern melbourne

GQ CHEV 350 HEI ignition Cutting out !!!

Post by GUEEY »

Hi there.

I am chasing a intermittent fault on my chev/GQ patrol.
when i am driving for about 30-60 minutes my truck cuts out and comes to a stop at the most inconvienent places.
It is like i have turned the key off while driving.
By the time i pop the bonnet and fiddle around for a few minutes i can turn the key and it will start agian.

The items i have replced so far.

Plugs
Leads
Coil, Cap & Rotor
Ignition modual.

I have checked the wiring to the dizzy and i just cant nail it.
i am a sparky and am good at chasing faults but this noe has my stumped.

Any Ideas ????

Cheers

Grant.
GU III TD42T UFI18G Cross Country IC, 20 PSI. Neeeeeed mooooore Fueeeeeel.
Posts: 14209
Joined: Sun Jan 11, 2004 11:36 am
Location: Adelaide

Post by -Scott- »

Where does your ignition module get it's trigger signal from?
Posts: 601
Joined: Mon May 24, 2004 9:50 am
Location: south eastern melbourne

Post by GUEEY »

-Scott- wrote:Where does your ignition module get it's trigger signal from?
I gets it signal from the coil that is fitted into the dizzy cap.
The modual replaces traditional points.
GU III TD42T UFI18G Cross Country IC, 20 PSI. Neeeeeed mooooore Fueeeeeel.
Posts: 443
Joined: Tue Oct 12, 2004 10:45 am
Location: Sailsbury-Brisbania

Post by JrZook »

GUEEY wrote:
-Scott- wrote:Where does your ignition module get it's trigger signal from?
I gets it signal from the coil that is fitted into the dizzy cap.
The modual replaces traditional points.
So ignition wise what havent you replaced? When you replaced the coil was that the ignition coil, or the pickup coil within the dizzy or both? Did you use the thermal conductive paste on your ignition modules when you re-mounted them? Sounds like a heat related problem. What type of HEI system are you running? Integral coil on the dizzy cap or external?

Cheers Dan
Posts: 601
Joined: Mon May 24, 2004 9:50 am
Location: south eastern melbourne

Post by GUEEY »

JrZook wrote:
GUEEY wrote:
-Scott- wrote:Where does your ignition module get it's trigger signal from?
I gets it signal from the coil that is fitted into the dizzy cap.
The modual replaces traditional points.
So ignition wise what havent you replaced? When you replaced the coil was that the ignition coil, or the pickup coil within the dizzy or both? Did you use the thermal conductive paste on your ignition modules when you re-mounted them? Sounds like a heat related problem. What type of HEI system are you running? Integral coil on the dizzy cap or external?

Cheers Dan
Yes i used the heat transfer paste.
The coil is the internal type fitted into the top of the dizzy cap.
There is no other coil or coil pack.
Is it possable that the ignition module might be a dud, i bought the gear fron Eagles in dandy.
The problem seemed to occur after i changed the module when i was chasing a rough idle problem.
GU III TD42T UFI18G Cross Country IC, 20 PSI. Neeeeeed mooooore Fueeeeeel.
Posts: 443
Joined: Tue Oct 12, 2004 10:45 am
Location: Sailsbury-Brisbania

Post by JrZook »

Yes it is possible that the new module could be faulty. Seems like you have covered pretty much everything else. Just one more thing tho, is the HEI a reluctor type trigger system? If so have you checked the gap between the iron veins and the pickup coil? Mmm thats all i can think of atm.
Hope it helps,
Dan
DL
Posts: 299
Joined: Wed May 31, 2006 8:33 pm
Location: Bellarine, Brackistan

Post by DL »

Posts: 601
Joined: Mon May 24, 2004 9:50 am
Location: south eastern melbourne

Post by GUEEY »

DL wrote:Hi,

Have a squiz here:

http://members.boardhost.com/blumx/msg/1189502986.html

cheers, DL
Holy Shit , that doesnt give me confirdence!!
GU III TD42T UFI18G Cross Country IC, 20 PSI. Neeeeeed mooooore Fueeeeeel.
DL
Posts: 299
Joined: Wed May 31, 2006 8:33 pm
Location: Bellarine, Brackistan

Post by DL »

Hi,

I posted it because it should give you confidence. The guy goes through every possible thing over time and gets a solution.

Rover motors apparently run quite happily under water with GM HEI dizzys.

Stick with it.

cheers, DL
Post Reply

Who is online

Users browsing this forum: No registered users and 12 guests