And has any one got any experience with removing the output shaft from the auto?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Toyota Auto Questions
Moderators: toaddog, Elmo, DUDELUX
Toyota Auto Questions
The gear looking thing on the output shaft shown below is for a speedo cable correct?
And has any one got any experience with removing the output shaft from the auto?
And has any one got any experience with removing the output shaft from the auto?
http://www.budscustoms.com.au
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
donk wrote:The rearmost one is the speedo drive gear
The larger one (strait cut teeth) in front is probably a speed sensor gear for the transmission control
Regards Don
so i can get rid of it if i am using after market computer and manual shifting on the auto
http://www.budscustoms.com.au
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Area54 wrote:It might be time for me to learn something here, but I thought the auto will only accept the fulltime chain drive case, with ADD?
correct you need an adaptor, i already have this auto nick, i am not going to buy another, but yes you are correct bell housing is identical to the 1UZ
http://www.budscustoms.com.au
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Bubs
Looks like the auto you have is from a 2WD which means you will have to swap in a 4WD auto output shaft which I gather was you main question
That would be a job for a trans shop and probably not cheap. Also means you will have to source a 4WD trans output shaft.
All the Toy 4WD autos require an ECU to operate correctly and although they are strong trannies they run very small convertors. I would guess the 2wd would be the same. Personallly I would recommend using a different trans.
JD
Looks like the auto you have is from a 2WD which means you will have to swap in a 4WD auto output shaft which I gather was you main question
That would be a job for a trans shop and probably not cheap. Also means you will have to source a 4WD trans output shaft.
All the Toy 4WD autos require an ECU to operate correctly and although they are strong trannies they run very small convertors. I would guess the 2wd would be the same. Personallly I would recommend using a different trans.
JD
Hey Bubs,
Looks like you have either a A340E or an A341 2wd trannie.
I'm facing the same delema at the moment. I'm looking at a 1UZ-FE into my 1985 HiLux and have a A341E.
The go is...If you want to keep this box and have RF1A Transfer case then you need:
1. Output shaft from a 4x4 trannie, ie A340F
2. Extension housing adapter from the same trannie, ie A340F
3. An adapter that will adapt item # 2 to the RF1A Transfer Case. You will also need a spline coupler...be wary that some RF1A's are 21 spline and some are 23 spline input shafts...the input shafts are interchangeable though.
If you are using the VF2A Chain Drive Transfer Case then it will bolt straight up to item #2 above.
Item # 3 above can be obtained from Marlin Crawlers. Sniff around this URL and you'll find what you're looking for ( http://www.4x4wire.com/toyota/tech/auto ... index2.htm ) or get onto the Marlin Crawler web site and go into the forum and post a question for cruzndave.
If you have a A341E you may want to reconsider things as their ratio's aren't that good for four wheel driving.
When you cost it up, you may be better trying to hunt down a A340F with transfercase (chain drive) and just bolt it in. If you are using a 1UZ-FE engine the belhousings are interchangable.
Personally, I'm trying to hunt down a R151F box and transfer case to bolt up to my 1UZFE using a Castlmaine bellhousing...Much stronger box, good ratios and a gear driven transfer case...but do you thinki can find one??? Might wind up with a R150F instead (different ratios with a chain driven transfer case).
Let me know what you think.
Cheers,
Shuey
Looks like you have either a A340E or an A341 2wd trannie.
I'm facing the same delema at the moment. I'm looking at a 1UZ-FE into my 1985 HiLux and have a A341E.
The go is...If you want to keep this box and have RF1A Transfer case then you need:
1. Output shaft from a 4x4 trannie, ie A340F
2. Extension housing adapter from the same trannie, ie A340F
3. An adapter that will adapt item # 2 to the RF1A Transfer Case. You will also need a spline coupler...be wary that some RF1A's are 21 spline and some are 23 spline input shafts...the input shafts are interchangeable though.
If you are using the VF2A Chain Drive Transfer Case then it will bolt straight up to item #2 above.
Item # 3 above can be obtained from Marlin Crawlers. Sniff around this URL and you'll find what you're looking for ( http://www.4x4wire.com/toyota/tech/auto ... index2.htm ) or get onto the Marlin Crawler web site and go into the forum and post a question for cruzndave.
If you have a A341E you may want to reconsider things as their ratio's aren't that good for four wheel driving.
When you cost it up, you may be better trying to hunt down a A340F with transfercase (chain drive) and just bolt it in. If you are using a 1UZ-FE engine the belhousings are interchangable.
Personally, I'm trying to hunt down a R151F box and transfer case to bolt up to my 1UZFE using a Castlmaine bellhousing...Much stronger box, good ratios and a gear driven transfer case...but do you thinki can find one??? Might wind up with a R150F instead (different ratios with a chain driven transfer case).
Let me know what you think.
Cheers,
Shuey
Modified Madness
yes, the 2wd trannie, this is what bj on roids runs in his R series are manuals are they not?
i want the auto, i drove BJ on Roids cruiser which has the same setup and i was impressed with how it crawled
thanks for the info though, more knowledge can only help when it comes time to adapt
i want the auto, i drove BJ on Roids cruiser which has the same setup and i was impressed with how it crawled
thanks for the info though, more knowledge can only help when it comes time to adapt
http://www.budscustoms.com.au
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
No worries Bubs.
Yep, the R series boxes are manual.
I guess the point i was looking to make was simply that if you have a A341E then the first gear ratio may be a bit lame, 2.53 as I am led to believe. A340E has 2.804. To put in perspective a TH700R4 has 3.06 first gear...Just a thought that's all.
Interested to see some snaps of the progress if you can.
Do you need that parts I mentioned? I know where you can get them.
Hey, how is BJ on Roids box going? Is it hanging in there? Is he running a A340E or A341E. Does he run a cooler on it?
Cheers,
Shuey
Yep, the R series boxes are manual.
I guess the point i was looking to make was simply that if you have a A341E then the first gear ratio may be a bit lame, 2.53 as I am led to believe. A340E has 2.804. To put in perspective a TH700R4 has 3.06 first gear...Just a thought that's all.
Interested to see some snaps of the progress if you can.
Do you need that parts I mentioned? I know where you can get them.
Hey, how is BJ on Roids box going? Is it hanging in there? Is he running a A340E or A341E. Does he run a cooler on it?
Cheers,
Shuey
Modified Madness
Shuey wrote:Hey, how is BJ on Roids box going? Is it hanging in there? Is he running a A340E or A341E. Does he run a cooler on it?
Cheers,
Shuey
he replaced it, but it leaked fluid and they dont like that
pretty sure he has a cooler, hed be the one to ask
http://www.budscustoms.com.au
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Like us and follow on facebook for up to date information of what we are working on and great random specials!
Custom Parts & Fabrication!
Ph: 0417 708 598
Shuey wrote:No worries Bubs.
Yep, the R series boxes are manual.
I guess the point i was looking to make was simply that if you have a A341E then the first gear ratio may be a bit lame, 2.53 as I am led to believe. A340E has 2.804. To put in perspective a TH700R4 has 3.06 first gear...Just a thought that's all.
Interested to see some snaps of the progress if you can.
Do you need that parts I mentioned? I know where you can get them.
Hey, how is BJ on Roids box going? Is it hanging in there? Is he running a A340E or A341E. Does he run a cooler on it?
Cheers,
Shuey
Yeah he is running some dodgy cooler. need to figure out where to measure the temps on it!! :(
IT is lasting fine, one had some water in it and ran really low on fluid and melted all the internals. But that was largely driver error. I then continued to drive on it, despite the fact that it was rooted.
hands and mums dont count!!!
Hey BJ on Roids,
Good to hear the Auto is sort of living.
I have deliberated on whether to go auto or manual for ages. My previous experience has been similar to yours...Keep em cool (keeping oil in them is a good thing too).
A couple of mates have run TH700's and they had a fair bit of grief with them over the years and seemed to regularly have them in for repairs.
Today i handed over the cash for an R151F (Aussie version, with chain transfer) and will hunt down a bellhousing from either Dellows or the Rod Shop...Hey rumour has it that the Rod Shop may be closing its doors...Don't quote me on that though. Be sad to see them go if that is the case.
Good to hear the Auto is sort of living.
I have deliberated on whether to go auto or manual for ages. My previous experience has been similar to yours...Keep em cool (keeping oil in them is a good thing too).
A couple of mates have run TH700's and they had a fair bit of grief with them over the years and seemed to regularly have them in for repairs.
Today i handed over the cash for an R151F (Aussie version, with chain transfer) and will hunt down a bellhousing from either Dellows or the Rod Shop...Hey rumour has it that the Rod Shop may be closing its doors...Don't quote me on that though. Be sad to see them go if that is the case.
Modified Madness
Who is online
Users browsing this forum: No registered users and 57 guests