I just took apart my steering hub knuckle to replace leakin inner seal, and i found every one of my sealing surfaces is eroded enough that theres no way a seal would do its job.
IE both the inner axle seal and the hub seal surfaces. Can you get speedy sleeves for these? CV is shot also, bloody Suzuki's cost so much to replace anything.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Seal surfaces eroded
You running WT diffs PJ? trail tough have a sale on Double toughs at the moment. Something like US$239 a pair + freight. Might be a good time to upgrade.
Work - KPD4X4.COM - KPD Industries Australian Distributor of Diesel Power Modules - Germany.
Play - dank's zook
Play - dank's zook
Ive never found CV's to break in my zook for some reason. I give em hell but have never broken one, so dont really need to upgrade.
Seriously thinkin of goin Hilux axles tho, could get front and rear for the same cost of buyin the bloody bits i need new.
The sealing surfaces are the pain in the ass, ill just use my old cv till it breaks, but having to replace whole components just cos one little surface is damaged grr...
Seriously thinkin of goin Hilux axles tho, could get front and rear for the same cost of buyin the bloody bits i need new.
The sealing surfaces are the pain in the ass, ill just use my old cv till it breaks, but having to replace whole components just cos one little surface is damaged grr...
speedi sleeves are made down to 12mm. so that will cover the size of a sierra drive shaft easily.
ifs its just pitting and you want a cheaper way out i've heard of guys through work that will get some magic metal, smear it across the pitted area and work it down till it can be cleaned up with a small amount of sanding. (this way is a little dodgey i know. i'm not reconmending it but its something that gets done. just make sure you clean ALL oil from the pitting so the putty takes to the metal)
or if its just a worn groove and easy way is to tighten your seal up. you can remove the spring from behind the sealing lip, and cut down the spring and rejoin them or just replace the spring all together with a slighty smaller o ring. (this method is used in alot of race boats)
weaves.
ifs its just pitting and you want a cheaper way out i've heard of guys through work that will get some magic metal, smear it across the pitted area and work it down till it can be cleaned up with a small amount of sanding. (this way is a little dodgey i know. i'm not reconmending it but its something that gets done. just make sure you clean ALL oil from the pitting so the putty takes to the metal)
or if its just a worn groove and easy way is to tighten your seal up. you can remove the spring from behind the sealing lip, and cut down the spring and rejoin them or just replace the spring all together with a slighty smaller o ring. (this method is used in alot of race boats)
weaves.
weaves wrote:or if its just a worn groove and easy way is to tighten your seal up. you can remove the spring from behind the sealing lip, and cut down the spring and rejoin them or just replace the spring all together with a slighty smaller o ring. (this method is used in alot of race boats)
weaves.
Exactly what i did, so far so good, but i have bigger concerns now lol
Who is online
Users browsing this forum: No registered users and 5 guests