Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Diff breathers

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 4073
Joined: Fri Apr 06, 2007 8:13 pm

Diff breathers

Post by lump_a_charcoal »

Just a heads up -

I have been looking for decent hose for diff breathers - I went to Clark Rubber, they have clear garden type hose that is good and strong, with a 4mm ID for about $4 a metre...

So, anyone searching, try there.

That is all.
Posts: 898
Joined: Wed Nov 29, 2006 6:16 pm
Location: Melb S/E

Post by NutterGQ »

wont last with heat and oil vapour, use fuel hose or vacum hose
My bitch has boost, Nutter Engineering Turbo GQ
Posts: 5
Joined: Sun Jun 21, 2009 8:03 pm
Location: Buronga NSW (near Mildura)

Post by searchin oz »

You could try your local Dixon stockist. Far cheaper than Clarke Rubber, I think I paid approx $35 for a 20metre roll of oil/petroleum hose 6mm.

www.dixonvalve.com.au
Posts: 4073
Joined: Fri Apr 06, 2007 8:13 pm

Post by lump_a_charcoal »

I'll try there if this stuff doesn't last...
Posts: 1009
Joined: Wed Jan 19, 2005 11:21 pm
Location: townsville

Post by brad-chevlux »

Don't use fuel hose, it will go like jelly with oil.
use ATF cooler hose, at least it will last
http://www.mothfukle-engineering.com/
Posts: 4073
Joined: Fri Apr 06, 2007 8:13 pm

Post by lump_a_charcoal »

Seriously, how much oil is likely to go through the hose, assuming the shiny side stays up?
I used clear plastic hose on my old hilux and it lasted fine for 3 years until I sold it, I never saw oil in the hose...
Posts: 898
Joined: Wed Nov 29, 2006 6:16 pm
Location: Melb S/E

Post by NutterGQ »

brad-chevlux wrote:Don't use fuel hose, it will go like jelly with oil.
use ATF cooler hose, at least it will last
I used to believe that but have been running it for 3 years on my PCV and no softer than new so I dunnno unless brands play a big part.
My bitch has boost, Nutter Engineering Turbo GQ
Posts: 5
Joined: Sun Jun 21, 2009 8:03 pm
Location: Buronga NSW (near Mildura)

Post by searchin oz »

brad-chevlux wrote:Don't use fuel hose, it will go like jelly with oil.
use ATF cooler hose, at least it will last
There is a specific Aust standard (it escapes me now) that covers oil/petroleum hose, we use it at work with no issues.
Posts: 474
Joined: Thu Apr 24, 2008 7:31 pm
Location: Canberra

Post by A.J. »

I use radiator overflow-bottle hose.
Cheap from supercheap etc. and has lasted for more than 1 year so far with no signs of degrade.
Run it for front and rear diffs, transfer and gearbox.
2001 GU Patrol DX wagon, TD42, Air Lockers, twin spare carrier, Barrett HF, 35" Treps, high pinion rear, Staun beadlocks, 60l Engel and more!
Banned
Posts: 142
Joined: Tue Feb 12, 2008 12:24 pm
Location: Queensland

Post by lukethedork »

I used 'clear plastic' hose, like lump_a_charcoal.
Lasted fine for the 6 months they were on my Hilux. I never saw any oil in the hose, and would presume that if oil was to get sucked up the hose, you would have other problems to work out....

Luke.
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

lukethedork wrote:I used 'clear plastic' hose, like lump_a_charcoal.
Lasted fine for the 6 months they were on my Hilux. I never saw any oil in the hose, and would presume that if oil was to get sucked up the hose, you would have other problems to work out....

Luke.
Clear hose "may" harden with oil fumwes and UV degradation. Also if it gets hot it can kink and temp block itself.

Bazzle
Posts: 379
Joined: Sat Aug 21, 2004 2:40 pm
Location: Epping , Vic

Post by BASSYK »

bazzle wrote:
lukethedork wrote:I used 'clear plastic' hose, like lump_a_charcoal.
Lasted fine for the 6 months they were on my Hilux. I never saw any oil in the hose, and would presume that if oil was to get sucked up the hose, you would have other problems to work out....

Luke.
Clear hose "may" harden with oil fumwes and UV degradation. Also if it gets hot it can kink and temp block itself.

Bazzle
UV degredation??

these lines will be under the car so id presume they wouldnt be getting much sun
Gu TD42t

[url]http://www.3rdrock4x4.com[/url]
Posts: 1081
Joined: Sun Jul 20, 2003 10:43 pm
Location: Melbourne

Post by B.D.R »

I have used that clear hose, look's like Bong tube, but smaller :lol: .

Ran this in a Rangie for years and never had a problem, and yes the Diff's DID have oil in them :D
Posts: 1400
Joined: Thu Nov 11, 2004 12:20 pm
Location: Mackay - Outerlimits; more extreme than your mum!

Post by phippsey »

Used 4-5mm black fuel hose.

Have been told to be careful it dosen't kink, ask Bru21. His kinked and blew the seals on the diff out
moorey wrote:All that aside, I am yet to be convinced that RUFF is anything other than a maniacal arse hat.
Posts: 1040
Joined: Fri Jun 29, 2007 7:57 pm
Location: yatala, halfway between brisbane and GC

Post by love ke70 »

if fuel hose goes gummy with oil, how do you run diesel through it?
97 GQ patrol coilcab. TD42, safari turbo kit with fiddled turbo, D-GAS kit. dyno results to come...
4inch lift, king springs, efs and procomp shocks
315/70R16 cooper ST's
found fuel economy...
Posts: 1400
Joined: Thu Nov 11, 2004 12:20 pm
Location: Mackay - Outerlimits; more extreme than your mum!

Post by phippsey »

love ke70 wrote:if fuel hose goes gummy with oil, how do you run diesel through it?
hmmm, interesting point.

To be honest I hadn't heard the bit about them gumming up

but I had heard about soft plastics bending over
moorey wrote:All that aside, I am yet to be convinced that RUFF is anything other than a maniacal arse hat.
Posts: 826
Joined: Mon Mar 20, 2006 1:08 pm
Location: Redcliffe

Post by berad »

I just used 5mm or so fuel hose, no gumming up, i dont imagine there will be.

1000000 things people say not to do, i do 900000 of them and it's fine, one off's etc etc get thrown around as a sure thing, just like everything in life, tv's, ifs etc etc haha
BBP Offroad
Boondall Backyard Performance

They call me the MR. throw cash at shiz til its comp specccccc
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

Post by 80's_delirious »

I used semi-rigid nylon air line with push-fit fittings. I got a threaded push-fit elbow fitting to replace the hose barb on the diff housings, ran lines from both diffs and gear box and transfer up in to the engine bay.

it was easy to loop it so it had spare length to allow diffs to droop with out it kinking, easy to run along chassis with a just few zip ties to brake lines ;)
I had the tube and fittings cost me about $20
Posts: 166
Joined: Tue Mar 04, 2008 4:04 pm
Location: SW Victoria

Post by djroberts »

so long as you use a hose containing Nitrile you should be fine. it's usually part of synthetic rubber comonly used in the automotive industry and resists degradation from fuels and oils. the higher the nitrile content the less likely it is to fail however, the hose will be stiffer. it is generally refered to as Nitrile butadiene rubber (NBR).

-Dave.
loose as a goose
Posts: 1570
Joined: Mon Aug 02, 2004 9:38 am
Location: Dalby

Post by Utemad »

I used the soft rubber irrigation hose from Bunnings 6mmID or so.

Been fine for over 2 years and being in a Rover it is oily all over and is fine :lol:

Cost next to nothing. I think I did both diffs for about $5.
At that price who gives a shit if you have to redo it every few years.
Land Rover Discovery series 1 V8
Posts: 1379
Joined: Mon May 07, 2007 8:28 pm
Location: West of Woodridge, North of Ipswich, South of Oxley, East of Wacol

Post by chikoroll_ »

fuel hose from supercheap - $3/metre
'98 Jackaroo
Bullbar, 32" muddies, Homebrew Timber centre console, Homebrew 3" Stainless rubber bend snorkel, Homebrew Steel rear bumper, Campervan interior
Posts: 31
Joined: Wed Jan 28, 2009 3:49 pm
Location: Caboolture

Post by big_al_31 »

I did some up for my lux a couple of weeks ago, i just went down to Repco they had everything there. Fuel hose, fuel filters, clamps and fittings. Cost me about 40 bucks total to get the lot. I never realized how helpful they are until then.
[b]Cheers Big Al[/b]
Post Reply

Who is online

Users browsing this forum: No registered users and 136 guests