Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

th700 to MQ transfercase

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 1595
Joined: Tue Dec 02, 2003 4:11 pm
Location: Warner, Brisbane Nth

th700 to MQ transfercase

Post by Spartacus »

MQ T100? remote transfer case behind v8 and T700.

Is there a minimun length for a jackshaft betwwen the auto and transfer?

Image

Its for a project with 105/110" Wheelbase.
MULL
Top
Posts: 1213
Joined: Wed Oct 26, 2005 8:25 pm
Location: SE Melbourne

Post by dank »

:D :D :D
this is the jackshaft between my auto and zook transfer. it'll end up about 85" wheelbase when I'm done.

Image
Work - KPD4X4.COM - KPD Industries Australian Distributor of Diesel Power Modules - Germany.
Play - dank's zook
Top
Posts: 1575
Joined: Thu Dec 28, 2006 6:50 pm
Location: Moronfield....

Post by nottie »

Top pic doesnt look straight
Top
Posts: 1595
Joined: Tue Dec 02, 2003 4:11 pm
Location: Warner, Brisbane Nth

Post by Spartacus »

nottie wrote:Top pic doesnt look straight
Top pic is an example. not my car
MULL
Top
Posts: 1321
Joined: Tue Aug 03, 2004 7:56 pm
Location: Jamisiontown NSW

Post by MARKx4 »

Couldnt you use a 60 series transfer instead of a MQ devoriced transfer? They are the same offset and im sure you can get a adaptor for it and they will give you alot more room.

Mark.
Its not cool, unless it's got boost :)
Top
Posts: 1595
Joined: Tue Dec 02, 2003 4:11 pm
Location: Warner, Brisbane Nth

Post by Spartacus »

yes, i could use any transfer with drivers side outputs.
trying to use what i have available, which is th700 and mq case


not really im being cheap and not spending $1000 on a adapter :roll:
MULL
Top
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

Ive mounted a zook transfer behind a Toyota box with nothing more than one uni joint joining the toyota output directly to the zook flange and had no vibration issues. As long as you get the allignments right and the mounting system is good you should have no issues.
Top
Posts: 1575
Joined: Thu Dec 28, 2006 6:50 pm
Location: Moronfield....

Post by nottie »

Hardy spicer sell a uni joint that will adapt the T700 output straight to the MQ divorced trans jack shaft. They also do one for a C4.

Get your point though on using what you have and being cheap.
Some times it works out to be very cool when stuff doesnt cost a bomb but gets the result.
As Tony touched on Try keep the jack shaft very short to save length.
Top
Posts: 1009
Joined: Wed Jan 19, 2005 11:21 pm
Location: townsville

Post by brad-chevlux »

the length of the shaft shouldn't mater so long as the angles of the unis are right.
http://www.mothfukle-engineering.com/
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 1 guest