Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

2.8 litre diesel rough idle

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 64
Joined: Fri May 01, 2009 10:53 am
Location: Sydney

2.8 litre diesel rough idle

Post by wompy »

Just wondering what could cause a rough idle or common problems with the 3L engine at idle.

Mine has brand new engine mounts and transfer case mount.

I've got my idle set to about 750rpm, because that's where it is the least rough, but it still seems vibrate the car heaps bad. What are these engines meant to idle at?

If anyone could help, or could tell me what fixed there rough idle that would be great

Cheers

Kyle
1996 LN 106 Dual Cab, 4 inch flex kits front and rear from www.locktup4x4.com.au 285/75r16 Mickey Thompson Baha MTZ, Alloy bull bar and side steps, Lightforce 240s
Posts: 64
Joined: Fri May 01, 2009 10:53 am
Location: Sydney

Post by wompy »

Ok so last weekend I did a service on the lux, I changed the oil, oil filter, cleaned k&n air filter, changed fuel filter, and then bled the fuel system with the primer and cracking each injector and then straight after that the idle was perfect.

But because the lux isnt my daily driver anymore, I had not driven it in 5 days and now the rough idle is back, by feeling the primer it feels that it has air in the system again, im not sure if im doing it right, do hilux's have like a bled tape or anything you are meant to crack before priming? And how could air get back into the fuel system?
1996 LN 106 Dual Cab, 4 inch flex kits front and rear from www.locktup4x4.com.au 285/75r16 Mickey Thompson Baha MTZ, Alloy bull bar and side steps, Lightforce 240s
Posts: 50
Joined: Sat Feb 07, 2009 7:41 am
Location: kellyville

Post by big_fyt »

mine had a similar problem a few months ago is yours sometimes really hard to start aswell?

i didn't come up with a solution for mine as i started using it everyday it seemed to go away
1997 solid front axel hilux, big plans for it.
Posts: 658
Joined: Wed Feb 13, 2008 5:41 pm
Location: Brissy

Post by yamaha__308 »

The lift pump/primers get old and start letting in air. My did this and was hard to start without priming. No bleed tap. They self bleed pretty well, usually not much more is needed after pumping up the lift pump.

Try tightening the fuel filter up a bit more, some don't like sealing much. Otherwise you might need a new lift pump.
Posts: 64
Joined: Fri May 01, 2009 10:53 am
Location: Sydney

Post by wompy »

Thanks guys, it starts with no problems at all but when cold it just rattles the car to bits, when warm its alot better but still shakes the mirrors that much at idle you cant see in them haha, my idle is set to 750.

Ill try tightening it a bit more, if not ill see how much a lift pump is, thanks.
1996 LN 106 Dual Cab, 4 inch flex kits front and rear from www.locktup4x4.com.au 285/75r16 Mickey Thompson Baha MTZ, Alloy bull bar and side steps, Lightforce 240s
Posts: 1490
Joined: Thu Nov 28, 2002 12:53 pm
Location: Brisbane - D'Bay

Post by Willy Hilux »

Just fit an electric pump off a VL Commadore etc before your lift pump. Herd it can help with power too.
AMADAXTREME Racing
Sponsors-
AmadaXtreme
Superior Engineering
www.superiorengineering.com.au/
Post Reply

Who is online

Users browsing this forum: No registered users and 24 guests