1. My feroza has a very loose front end, like steering a dodgey rowboat?
I am not mechanicaLLY minded to start, the front right has movement when moved towards me, held at 10 and 2.... could it be bearings?
2. ALso, i need bigger tyres and rims as i have 235/75/15's and there is still room to move, ie, the guards arent full, what is the next tyre size possible with only a 2" bodylift please?
3. Temp guage doesnt work ? any ideas?
4. Somewhere on the sunshine coast QLD worthy of gettiing work done ?
I want suspension done ( 2" lift)
wheels 15" dynamics with a/t or muddies
snorkel
extractors /exhaust
front bar
I waffle on a bit so if you can help me out on any of this i would be grateful, also, if you make custom snorkels or bars let me know i will pay good $$$ for good gear
thanks
Chris
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
All over the shop !!!
Moderator: Tiny
All over the shop !!!
91 stock Feroza Ogre green in colour
Want heaps of stuff but there is SQAT available...
SWAPS FOR GQ + cash ?
07 54295854
pm
Want heaps of stuff but there is SQAT available...
SWAPS FOR GQ + cash ?
07 54295854
pm
Steering: Most likely your idler arm is shot. You could try getting a new poly bush for it, otherwise replace it altogether = more expensive.
Tyres & rims: I'd tend to go muddies... prolly a 275/75 15 or a 30 X 9.5
Temp gauge, check the wire is connected to the sender/check the sender.
Tyres & rims: I'd tend to go muddies... prolly a 275/75 15 or a 30 X 9.5
Temp gauge, check the wire is connected to the sender/check the sender.
bru21 wrote:What happens in goat, stays in goat!
will start on it tomorrow
AJ's on the money.
As for lift.... to save yet another thread on this try the search facility - you'll find lots of valuable information on the pro's and con's.
Summary - its easy to do badly ( cheap ) and hard to do well ( expensive ).
As for lift.... to save yet another thread on this try the search facility - you'll find lots of valuable information on the pro's and con's.
Summary - its easy to do badly ( cheap ) and hard to do well ( expensive ).
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Had a look at it today, there is a bar which i assume is the torsion bar, (has a section about 5 inches long where it looks like you can adjust it )
Well where this connects to what i think is the idler arm it is loose as a bit on the right and heaps on the left so i assume i need to replace the bushes etc ?
See, i honeslty have no idea lol need pics to show you
Well where this connects to what i think is the idler arm it is loose as a bit on the right and heaps on the left so i assume i need to replace the bushes etc ?
See, i honeslty have no idea lol need pics to show you
91 stock Feroza Ogre green in colour
Want heaps of stuff but there is SQAT available...
SWAPS FOR GQ + cash ?
07 54295854
pm
Want heaps of stuff but there is SQAT available...
SWAPS FOR GQ + cash ?
07 54295854
pm
I think your describing the tie rods...
Can i suggest you download the Feroza manual from www.warfs.org , or at least the bits you need ( get the lot if bandwidth isn't an issue )
In the long run it will be very useful even if you know very little at the moment, you"ll pick stuff up as you go along. We all did it this way....
That way we'll at least be calling things the same - at the moment its a bit hard to start describing test procedures when we both aren't working with the same "words"
Can i suggest you download the Feroza manual from www.warfs.org , or at least the bits you need ( get the lot if bandwidth isn't an issue )
In the long run it will be very useful even if you know very little at the moment, you"ll pick stuff up as you go along. We all did it this way....
That way we'll at least be calling things the same - at the moment its a bit hard to start describing test procedures when we both aren't working with the same "words"
( usual disclaimers )
It seemed like a much better idea when I started it than it does now.
It seemed like a much better idea when I started it than it does now.
Who is online
Users browsing this forum: No registered users and 1 guest