Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Want to fit a Holden stroker to a 88 hi-line RRC
Moderator: Micka
Want to fit a Holden stroker to a 88 hi-line RRC
Want to fit a Holden stroker to a 88 hi-line RRC . Will probably inject it using a VS /VT 808 and Tunerpro . Going to use a R380 originally , but I have 2 T700's sitting in the shed as well . It appears that no one does a Transfer case adapter to adapt the T700 to the LT230 . As the T700/4L60 is totally different to a T400 and way longer than a 4l80E and wondering has anybody adapted a T700 to the LT230 . The curent 355 runs 250RWKW so thats around 400HP at the fly on straight LPG but I wont be able to fit enough tanks to give enough range , so back to EFI
Well I rang Marks 4WD adapters , and as I said the 4l80E is nothing like the 4L60 and they do not and never have made an adapter for the 4L60 .
CRS and Dellows said the same , never made anything for the 4L60 . Dont confuse the 4l60 or 4L60E with a 4L80E , thet are vastly diferent ,The 4L80E is usually used in the Chev /GM Four wheel drives , the 4L60 is a car transmission . Output shaft is 3 inches longer , and has a totally different spline and spline length and spline position and extension housing bolt pattern.
CRS and Dellows said the same , never made anything for the 4L60 . Dont confuse the 4l60 or 4L60E with a 4L80E , thet are vastly diferent ,The 4L80E is usually used in the Chev /GM Four wheel drives , the 4L60 is a car transmission . Output shaft is 3 inches longer , and has a totally different spline and spline length and spline position and extension housing bolt pattern.
Hautech in brisbane may still do one for you? LT230 / T700 that is. No funny angle. To fit its run on slight angle so the front output clears the oil pan on the auto. Factory LT230 to ZF is on a bigger angle.
The input gear from memory needs to be bored out and the slip yoke shaft off the end of the commo driveshaft is then pressed in and welded. From there its just 2 plates cut to bolt to each face and a length of the right size pipe joining them together. The input gear when fitted to the auto has the slip yoke (thats welded into it) goes thru the adapter and slides on the end spline of the t700. Easy as.
The input gear from memory needs to be bored out and the slip yoke shaft off the end of the commo driveshaft is then pressed in and welded. From there its just 2 plates cut to bolt to each face and a length of the right size pipe joining them together. The input gear when fitted to the auto has the slip yoke (thats welded into it) goes thru the adapter and slides on the end spline of the t700. Easy as.
Thanks guys , after finding out why the 4L60 is not done by the major conversion mobs , Ive just done a swap with one of my Drag racing Trimatics and stally for a good 4L80E ,Going to get the Compucontrol as well so wont need for a BCM ,.
Now , how to graft a couple a Nascar spec 3.8 ratio 9 inch diff centres into RR diff housings ?
Now , how to graft a couple a Nascar spec 3.8 ratio 9 inch diff centres into RR diff housings ?
Nottie, as you know with a 9 Inch , you can go fron ratios 2.3:1 to almost 6:00 : 1 , cheaply and easily ,Ive just got 2 9 inch diff centres with 3.8 ratio . if I need a lower gear Ill get someof those rock crawler low range gear sets . I wasnt really going down the road of building some sort of Dysfunctional Rock crawler . I was thinking the opposite , perhaps bagging it and slammin it , then down to Whoopass wednedays for a 13 sec quarter . What eve rparts your hair !!!!! LOL
Who is online
Users browsing this forum: No registered users and 18 guests