Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Wt vs nt diff centres
Wt vs nt diff centres
Hey does any body no if wide track diff centres are the same as narrow tracks. Reason bein i might be able to get a set of air lockers cheap out of a holden drover with compressor
me217
1985 suzuki mighty boy : mods, f8b
1990 toyota mr2 gt import : mods, turbo timer, short shifter, 2.5" exhaust
1992 suzuki sierra : mods, g16b mpfi, 235's/75, snorkel & lift on the way.
1985 suzuki mighty boy : mods, f8b
1990 toyota mr2 gt import : mods, turbo timer, short shifter, 2.5" exhaust
1992 suzuki sierra : mods, g16b mpfi, 235's/75, snorkel & lift on the way.
except for ratio, they are the same internally. NT=3.9, WT=3.7
But if you buy a pair, you'll have matched ratios
Externally the NT has a smaller drive flange. You can either change the flange on the diff, or change the flange on your tailshafts to get them to match.
But if you buy a pair, you'll have matched ratios
Externally the NT has a smaller drive flange. You can either change the flange on the diff, or change the flange on your tailshafts to get them to match.
Wheeling on completely wicked angles, without even looking stable.
u will have to take the big nut off both diff centers where your tailshaft joins and knock the flanges off, and swap then over
[quote="MissForby"]"I like Pillows. I'm not allowed anything hard" :D[/quote]
94 vitara, rear air locker, 31's, dual battery, custom front and rear tube bars, chopped guards, reduction gears
94 vitara, rear air locker, 31's, dual battery, custom front and rear tube bars, chopped guards, reduction gears
Once you undo the pinion flange nut, you need to replace the crush sleeve or there's no guarantee you'll achieve correct bearing preload and shorter bearing life & damaged gears are the result.danssurf82 wrote:u will have to take the big nut off both diff centers where your tailshaft joins and knock the flanges off, and swap then over
Much better to swap driveshaft flanges.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
there is a 99.99999999% chance that you WILL achieve the right preload and pattern. don't be shy.Gwagensteve wrote:Once you undo the pinion flange nut, you need to replace the crush sleeve or there's no guarantee you'll achieve correct bearing preload and shorter bearing life & damaged gears are the result.danssurf82 wrote:u will have to take the big nut off both diff centers where your tailshaft joins and knock the flanges off, and swap then over
Much better to swap driveshaft flanges.
Steve.
lwb 1.6efi,4sp auto,f&r airlockers,dual t/cases.custom coils.builder of ROAD LEGAL custom suzukis...and other stuff.
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
CAD modelling-TECH drawings-DXF preparation.
http://www.auszookers.com/index.php
Wonder why suzuki don't say you can reuse the crush sleeve then?
I've seen too many trashed gears from incorrect setup to advocate cranking the nut up and calling it good. I don't believe it's a good idea.
Suzuki are very specific about when something can be pulled and gunned back up - example - transfer case flanges can be pulled and replaced without issue, but diffs can't according to them..... then again, what do they know?
It might be possible, but from the preloads and patterns I've seen suzuki diffs must be set up by someone who knows exactly what they are doing or they will last months.
I guess it depends on the $$ in the diff and the use of the car, but if I depended on it, I'd pay for a new crush sleeve as suzuki recommend (or get a solid spacer set up.)
Just my 2C.
Steve.
I've seen too many trashed gears from incorrect setup to advocate cranking the nut up and calling it good. I don't believe it's a good idea.
Suzuki are very specific about when something can be pulled and gunned back up - example - transfer case flanges can be pulled and replaced without issue, but diffs can't according to them..... then again, what do they know?
It might be possible, but from the preloads and patterns I've seen suzuki diffs must be set up by someone who knows exactly what they are doing or they will last months.
I guess it depends on the $$ in the diff and the use of the car, but if I depended on it, I'd pay for a new crush sleeve as suzuki recommend (or get a solid spacer set up.)
Just my 2C.
Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Who is online
Users browsing this forum: No registered users and 1 guest