Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

BEST SILICON ON TURBO MANIFOLD 80 SER

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 70
Joined: Wed May 20, 2009 5:47 pm
Location: WARNEET

BEST SILICON ON TURBO MANIFOLD 80 SER

Post by tiny80 »

HI THERE I HAVE A CUSTOM TURBO MANIFOLD THAT ALL WAYS LEAKS
ITS MADE FROM 12MM PLATE ITS BEEN MILLED 3 TIMES WITH NO LUCK
ANYONE GOT ANY IDEARS HOWW TO SEAL IT UP THE BEST
IKNOW THE FOLLOWING ARE REQ ED
NEW GASKET ? STEEL PLATES OR PRESS STEEL WITH HOLES
SILICON ? LOCKTITE COPPER TYPE OR ANY THING ELES BETTER?
NOTE THE IS FOR A 1FZFE MOTOR 4.5 L RUNNING STRAIGHT GAS
ALL HELP IDEARS WOULD BE GREAT
lifted and locked 80 series landcrusier
turbo 1 fzfe straight gas 35" claws and heaps more crap inside
Top
User avatar
Ice
Posts: 2429
Joined: Sun Jul 25, 2004 6:52 pm
Location: Central Coast, NSW

Post by Ice »

you could try a plain copper gasket, it you already have one and its leaking try annealing it and bolting it back together

strange is leaking if its been milled 3 times... is the machine setup right or is it taking out material in the middle ? eg have you checked its flat
xxxx wrote:
:bad-words: :snipersmile:
Top
Posts: 70
Joined: Wed May 20, 2009 5:47 pm
Location: WARNEET

MANIFOLD

Post by tiny80 »

EACH TIME IS SWEET FOR 2000KM OR SO THEN LECKS
FIRST MILL JOB WAS SHIT JOB 2 ITS WAS AVE BUT FOR FREE
BUT THE LAST TIME IT WAS GREAT I PAID FOR IT THOUGH
WHERE CAN I GET A COPPER ONE MADE
lifted and locked 80 series landcrusier
turbo 1 fzfe straight gas 35" claws and heaps more crap inside
Top
Posts: 876
Joined: Sun Dec 21, 2008 4:28 pm
Location: Gympie

Post by Matt_85Lux »

Are the nuts still tight when it starts to leak, I had that problem with my setup at first.
If ignorance is bliss, then why aren't there more happy teenagers?
Top
Posts: 438
Joined: Tue Feb 20, 2007 7:34 am
Location: Gordonvale Queensland

Contact:
Contact flyology

Post by flyology »

It is being tightened to the correct factory torque settings, and the correct sequence?
My 60 series rebuild....
http://www.outerlimits4x4.com/ftopic103004.php&highlight=

http://www.flyology.com

2006 CRV Sport (wifes car)
Top
Posts: 2097
Joined: Tue Aug 12, 2003 6:50 pm
Location: wollongong

Post by dow50r »

std toyota gasket is sandwhich design / has expansion built in for alloy expansion and contraction.
Confucious say...man who argue with idiot, worserer himself
Top
Posts: 117
Joined: Sun Mar 25, 2007 9:45 pm
Location: rocky

Post by crazy eyes »

i found on mine that i had to retension the studs every couple of months i did that for 3 or 4 times then it stayed good and didnt leak. i allso use the factory commetic gasket with ultra copper silicon . if it still leeks then the problem could be that it needs a bracket to support the manifold from the block to the manifold as there is a far bit of weight hanging on it and when it gets hot it destorts and then leeks.
cheers jason
Top
Posts: 70
Joined: Wed May 20, 2009 5:47 pm
Location: WARNEET

manifold

Post by tiny80 »

i have removed the maniflod now
i have just got new factory gaskets steel press type
fitting up will be to factory specs and copper silicon
if there is a next time it will be copper
it has 2 brackets that hold turbo assembly so stress should not be a problem
lifted and locked 80 series landcrusier
turbo 1 fzfe straight gas 35" claws and heaps more crap inside
Top
Posts: 550
Joined: Tue Mar 04, 2008 7:40 pm
Location: Gympie Qld

Post by fester2au »

You mention the manifold has been milled 3 times and still not great. Have you actually looked at the other side of the equation (didn't say head or turbo side) to ensure that both mating surfaces are dead flat. Have you also radiused the bolt holes to ensure any studs if you have any aren't pulling the hole edge up and causing a leak to start there.
Top
Posts: 12
Joined: Sun Mar 28, 2010 6:38 pm
Location: Qld

Post by Roboat »

Run two gaskets is always an option that i've had a lot of success with.
Top
Posts: 12
Joined: Sun Mar 28, 2010 6:38 pm
Location: Qld

Post by Roboat »

Run two gaskets is always an option that i've had a lot of success with.
Top
Posts: 1042
Joined: Mon May 05, 2008 6:33 pm
Location: MACKAY

Post by SIMMO84 »

We use locktite 5900 on any manifolds we are unsure of.
Wtb, 105 series rear tyre carrier, alloys and tyres.
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 87 guests